background image

                                                                                                                               

Quantum 1121

 9

www.pridemobility.com

I I .   S A F E T Y

To navigate up over a kerb or stationary obstacle:

1. Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle. See figure 2.

2. Increase the forward speed just before the front wheels come in contact with the obstacle.

3. Reduce the forward speed only after the rear wheels have cleared the obstacle.

To navigate down a kerb or stationary obstacle:

1. Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle. See figure 2.

2. Reduce the forward speed just before the front wheels come in contact with the obstacle.

3. Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a level surface.

WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher

than 5 cm (2 in) unless you have the assistance of an attendant. 

WARNING! Do not attempt to have your power chair proceed rearward down any step, kerb, or

other obstacle. This may cause the power chair to tip. 

Stairs and Escalators

Power chairs are not designed to travel up or down stairs or escalators. Always use a lift. 

WARNING! Never use your power chair to negotiate steps or escalators. 

Doors

„

Determine if the door opens toward or away from you.

„

Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently

      and slowly rearward to pull the door open.

Lifts

Modern lifts have a door edge safety mechanism that, when pushed, reopens the lift door(s).

„

If you are in the doorway of a lift when the door(s) begin to close, push on the rubber door edge or allow the

      rubber door edge to contact the power chair and the door will reopen.

„

Use care that handbags, packages, or power chair accessories do not become caught in lift doors.

Lift/Elevation Products

If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in

transportation. Pride recommends that you closely review the instructions, specifications, and safety information

set forth by the manufacturer of the lift/elevation product before using that product.

WARNING! Never sit on your power chair when it is being used in connection with any type of

lift/elevation product. Your power chair was not designed with such use in mind and any damage

or injury incurred from such use is not the responsibility of Pride.

Motor Vehicle Transport

Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The

power chair should be stowed in the boot of a car or in the back of a truck or van with the batteries removed and

properly secured. In addition, all removable power chair parts, including the armrests, seat, front riggings, con-

troller, and shrouds should be removed and/or properly secured during motor vehicle transport.

WARNING! Do not sit on your power chair while it is in a moving vehicle. 

WARNING! Always be sure your power chair and its batteries are properly secured when it is

being transported. Batteries should be secured in an upright position and protective caps should

be installed on the battery terminals. Batteries should not be transported with any flammable or

combustible items.

Содержание Quantum 1121








































Отзывы: