background image

6379 Clark Ave Suite 280, Dublin CA 94568 USA    

 

 Tel: +1 510 785 0510

www.acutherm.com • [email protected]

Copyright ©Acutherm 2012

Subject to change without notice.

Ten Year Warranty

Acutherm warrants that its Therma-Fuser diffusers, exclusive of any options and accessories (whether factory or field installed) 
shall be free from defects in material or workmanship for a period of ten (10) years from the date of shipment and agrees to repair 
or replace, at its option, any parts that fail during said ten (10) year period due to any such defects which would not have occured 
had reasonable care been taken, provided that such parts have been inspected by Acutherm and found defective and provided the 
diffusers have been given normal and proper usage and all parts and controls remain unaltered. Acutherm makes NO WARRANTY 
OF MERCHANTABILITY OF PRODUCTS OR OF THEIR FITNESS FOR ANY PURPOSE OR ANY OTHER EXPRESS OR IMPLIED 
WARRANTY WHICH EXTENDS BEYOND THE LIMITED WARRANTY ABOVE. ACUTHERM’S LIABILITY FOR ANY AND ALL LOSSES 
AND DAMAGES RESULTING FROM DEFECTS SHALL IN NO EVENT EXCEED THE COST OF REPAIR OR REPLACEMENT OF PARTS 
FOUND DEFECTIVE UPON EXAMINATION BY ACUTHERM. IN NO EVENT SHALL ACUTHERM BE LIABLE FOR INCIDENTAL, 
INDIRECT OR CONSEQUENTIAL DAMAGES OR DAMAGES FOR INJURY TO PERSONS OR PROPERTY. Acutherm shall not be 
responsible for freight to or from its plant in connection with the inspection, repair or replacement of parts under the terms of this limited 
warranty nor for cost of removal or installation.

Содержание Acutherm THERMA-FUSER SYSTEMS







Отзывы: