Presys PCON-Y17 Series Скачать руководство пользователя страница 66

Страница: 66 / 68

PRESYS



Instruments

PCON-Y17

Page 60

MEASure[:SCALar]:VOLTage[:DC]?

Description:

Voltage Input (Auxiliary) Reading.

Parameters:

---

Response:

V Reading

OUTPut:MODE <mode>

Description:

Sets the Pressure Operation Mode.

Parameters:

VENT | CONTrol | MEASure

Response:

---

3 - Maintenance

3.1. Replacing the Current Input Fuse

To replace the PCON-Y17 mA Input (Auxiliary) fuse, proceed as follows:

- Rotate the fuse holder counterclockwise (see see

Fig. 01

for DT Version or

Fig. 03

for

Rack Mounting Version

– Fuse mA input). Try to use a plastic tool to avoid damaging the

fuse holder;

- The fuse holder will be released;

- Pull the fuse holder and remove the fuse;

- Place the spare fuse (Time-Lag Type Fuse 32 mA / 250 V / 5 x 20mm).

3.2. Replacing the Power Supply Fuse

In case of blow, the 1 Amp fuse (Time Delay Type Fuse 1 A / 250 V / 5x20mm),

placed within the power supply socket on the rear can be replaced.

The fuse may blow due to a voltage spike in the mains or a calibrator component

fault. Replace the fuse once. If a second fuse blows again, it is because the fault is not
that simple. In this case, contact the

Presys

technical support.

presys

Содержание PCON-Y17 Series





































































Результаты поиска

Содержание PCON-Y17 Series

Отзывы:

Похожие инструкции для PCON-Y17 Series

Бренды по названию

Популярные бренды

Presys PCON-Y17 Series, Техническое руководство

Результаты поиска

Содержание PCON-Y17 Series

Отзывы:

Похожие инструкции для PCON-Y17 Series

Бренды по названию

Популярные бренды