Prestige 1124316 Скачать руководство пользователя страница 15

Страница: 15 / 16

128-9480

15 of 16

Page 15

COMPLETING THE INSTALLATION:

After you have confirmed the operation of the Remote Start unit and tested all the safety

features of the system:

1. Mount the control module up and behind the dash securing it in place with cable ties

or screws. Be certain that the chosen mounting location will not inhibit any of the

controls of the vehicle.

2. Securely harness and tie all wiring up and away from all hot and moving parts that they

may come in contact with under the dash board or in the engine compartment areas.

CAUTION:

Particularly avoid the area around the steering shaft and column, as wires

can wrap around these mechanisms and impair the safe operation of the

vehicle.

3. Apply the Caution Labels supplied with this kit to a conspicuous area in the engine

compartment. Make sure to clean the surface before affixing the label.

4. Check the vehicle’s wipers, lights, horn, etc.... to insure proper operation.

5. Replace all panels that were removed during installation, and retest the system.

6. Explain all activated features and safety systems associated with Remote Start Unit

installed to the customer.

Содержание 1124316

















Результаты поиска

Содержание 1124316

Отзывы:

Похожие инструкции для 1124316

Бренды по названию

Популярные бренды

Prestige 1124316, Руководство по установке

Результаты поиска

Содержание 1124316

Отзывы:

Похожие инструкции для 1124316

Бренды по названию

Популярные бренды