PRESIDENT Grant II, Руководство пользователя

Страница: 34 / 56

34
Memory Channel Scan Mode
During the scan, press then
MEM
key (
10
) for activate the
Memory Channel
Scan Mode
and scan only the channels stored in memories. A new press in
the
MEM
key (
10
) return to the
All Channel San Mode
.
The scanner starts automatically in upward direction 3 seconds after the
transmission stops and no key is pressed during 3 seconds. The scanning
can restarts also in a downward direction turning the channel selector knob
counter clockwise or pressing the
DN
key on the microphone. In upward
direction turning the channel selector knob clockwise or pressing the
UP
key
on the microphone.
Press the PTT pedal ( 17 ) to stop the SCAN function.
M3
See the
MEM
function on page 32.
14) SWR ~ ROGER ~ M2
SWR
(short press)
Use the
SWR
key to change the meter function:
S/RF
: the bargraph indicates the received signal strength and transmitted
power. “S/RF” is displayed on the LCD.
SWR
: the bargraph indicates the received signal strength and the SWR (Stand-
ing Wave Ratio) reading.”S”and “SWR” are displayed on the LCD. (See §5
page 30) .
ROGER
(long press)
The icon “ ” appears on the display when the function is active. The Roger
Beep sounds when the
PTT
pedal (
17
) of the microphone is released in order
to let your correspondent speak. Historically as CB is a “simplex” communi-
cation mode, it is not possible to speak and to listen at the same time (as it
is the case with a telephone). Once someone had finished talking, he said
“Roger” in order to prevent his correspondent that it was his turn to talk. The
word “Roger” has been replaced by a significant beep. There comes “Roger
beep” from.
Note: the ROGER beep also sounds in the loudspeaker if the
KEY BEEP
function
is active. If the
KEY BEEP
function is not active, only the correspondent can
hear the ROGER Beep.
M2
See the MEM function on page 32.
15) AM/FM/USB/LSB ~ LOCK ~ M1
AM/FM/USB/LSB
(short press)
This key allows selecting the modulation mode AM, FM, USB or LSB. Your
modulation mode has to correspond to the one of your correspondent.
Frequency Modulation / FM: for nearby communications on a flat open field.
Amplitude Modulation / AM: communication on a field with relief and ob-
stacles at middle distance (the most used).
Upper and Lower Side Band / USB-LSB: used for long distance communica-
tions (according to the propagation conditions).
LOCK
(long press)
Allows to lock all the keys on the front panel, the rotary knob and UP/DN
keys on the microphone ( 4 ). An error beep sounds when a key is used and
the LOCK function is activated. A long press on LOCK activates/deactivates
the LOCK function. appears on the display when the function is activated.
Transmission (mike or vox) and reception remain active.
M1
See the MEM function on page 32.
16) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the set-
ting of the equipment into the dashboard easier.
See cabling diagram page 52.
17) PTT
Transmission key, press to transmit a message, is displayed and release
to listen to an incoming communication.
TOT (Time Out Timer)
If the
PTT
key (
17
) is pressed for more than 5 minutes, CHANNEL and
starts
blinking, the transmission ends. The TX time out tone will sound until the PTT
key ( 17 ) is released.
A) DC-POWER TERMINAL (13,2 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω , Ø 3,5 mm)
D) JACK FOR OPTIONAL VOX MIKE (Ø 2.5 mm)
English