11
- When the color is set, long press the
NB
key (
5
) or the
PTT
switch
(
11
). A beep sounds, the characters of the color are displayed
during 1 second.
5) RESET
(
EMG
key)
- Turn on the power while pressing the
EMG
key (
7
) to reset to the
factory settings.
- “
rS
” blinks in the display.
- Press the
NB
key (
5
) for 1 second to confirm.
D) FUNCTIONS WITH PTT SWITCH
4 more functions are available. To activate the function press and
hold the
PTT
switch (
11
) and press the function key. Repeat this
process to deactivate the function.
1) TALKBACK
(
PTT
+
NB
key)
The
TALKBACK
function
can be activated or deactivated as follows:
a)
Press and hold the
PTT
switch (
11
)
b)
Short press on
NB
key (
5
). Current
TALKBACK
level blinks 3 times
allowing you to adjust this level.
When function is activated,
“TB”
appears on the display.
This function allows to ear your own modulation with the CB speaker.
2) TALKBACK LEVEL
(
PTT
+
s
/
t
)
- At step
b)
adjust the
TALKBACK
level using the
s
/
t
keys (
3
).
- When the function is
on
and
“TB”
is shown on the display, press
and hold the
PTT
switch (
11
), then use the
s
(
3a
) /
t
(
3b
) keys to
select the level. 9 levels from
01
to
09
.
3) PA
(
PTT
+
CB/WX
key)
-
Press and hold the
PTT
switch (
11
)
- Short press on
CB/WX
key (
6
) to alternate between
CB
and
PA
(Public Address) mode. An external loud speaker can be con-
nected to your ANDY II FCC by the
PA jack
plug situated on the
back panel PA.SP (
D
). The CB message received or transmitted
into the microphone will be directed towards the external speaker
and be amplified. Adjust the
PA
volume with
VOL
key (
1
).
When
PA
mode is activated,
“PA”
and
“AM”
blink alternatively.
When
PTT
switch (
11
) is pressed,
“PA”
replace the active channel
on the display. Release the
PTT
switch (
11
) to display again the
active channel.
4) NOISE GATE
(
PTT
+
VOX
)
- Press and hold the
PTT
switch (
11
).
- Short press the
VOX
key (
8
) to activate (
On
) or deactivate (
OF
)
the
NOISE GATE
. “
” Is displayed when the function is active.
Noise Gate:
Prevents amplification of background noise. This results
in optimized signal levels.
E) TECHNICAL CHARACTERISTICS
1) GENERAL
- Channels
: 40
- Modulation modes
: AM
- Frequency ranges
: from 26.965 MHz to 27.405 MHz
- Weather channels
: 162.400 MHz to 162.550 MHz
- Antenna impedance
: 50 ohms
- Power supply
: 13.8 V / 27.6 V
- Dimensions
: 4.92 (W) x 7.09 (D) x 1.77 (H) inches
125 (W) x 180 (D) x 45 (H) mm
- Weight
: ~ 1.98 lbs / 0.9 kg
- Accessories supplied
: Electret microphone with support,
mounting cradle, screws.
- Filter
: ANL (Automatic Noise Limiter) built-in
2) TRANSMISSION
- Frequency allowance
: +/- 200 Hz
- Carrier power
: 4 W
- Transmission interference
: inferior to 4 nW (- 54 dBm)
- Audio response
: 300 Hz to 3 KHz
- Emitted power in the adj.
channel
: inferior to 20 µW
- Microphone sensitivity
: 7 mV
- Maximum drain
: 1.7 A at 13.8 V / 0.85 A at 27.6 V
- Modul. signal distortion
: 2 %
EnglishEnglish
Содержание ANDY II FCC
Страница 1: ...Owner s manual Manual del usuario Manuel d utilisation Manual do usu rio...
Страница 53: ...53...
