Premio MSI ATX TX5 Скачать руководство пользователя страница 98

Страница: 98 / 98

CHAPTER 4

AMI

BIOS USERS GUIDE

Description of the item on screen follows:

CPU Thermal Setup

This is for setting the CPU temperature. You must leave this on the

default setting of 60.

CPU Current Temperature

This will show the CPU Current temperature.

Thermal Slow Clock Ratio

This will show the thermal slow clock ratio

CPU Temperature Display

If set to yes, during boot-up this will show the CPU temperature.

System Temperature Set

This is for setting the system temperature. You must leave this on

the default setting of 50.

System Current Temperature

This wil show the current temperaure of the system.

Chassis Intrusion

During Enabled, the on-board chassis intrusion sensor will monitor

any intrusion on the chassis.

Power FAN Message Display/CPU FAN Message Display

If set to yes, if any of the fan malfunction then it will show warning

messages.

System Temperature Display

If set to yes, if the temperature gets to high or to low, this will show

warning messages.

4-26

Содержание MSI ATX TX5



































































































Результаты поиска

Содержание MSI ATX TX5

Отзывы:

Бренды по названию

Популярные бренды

Premio MSI ATX TX5, Руководство пользователя

Результаты поиска

Содержание MSI ATX TX5

Отзывы:

Бренды по названию

Популярные бренды