manualshive.com logo in svg

Premio MSI ATX TX5, Руководство пользователя

Поделиться
Скачать
Premio MSI ATX TX5 Скачать руководство пользователя страница 69

CHAPTER 3

AWARD

®

 BIOS SETUP

3-32

Onboard IR Controller

Enabled/Disabled

The system has an on-board Super I/O
chip with an IR controller.  Choose
“Enabled” to use the on-board IR
controller for accessing the IR devices.
Otherwise choose “Disabled” to use the
off-board IR controller.

IR Mode

This function is for choosing which IR mode to use.  Leave this on

the default setting of Irda.

Onboard Parallel Port

Disabled

There is a built-in parallel port on the
on-board Super I/O chipset that
provides Standard, ECP, and EPP
features.  It has the following options:

Disable
3BCH/IRQ7

Line Printer port 0

278H/IRQ5

Line Printer port 2

378H/IRQ5

Line Printer port 1

Onboard Parallel Mode

SPP  : Standard Parallel Port
EPP  : Enhanced Parallel Port
ECP :  Extended Capability Port

To operate the onboard parallel port as
StandardParallel Port only, choose
“SPP.”  To operate the onboard parallel
port in the ECP and SPP modes simulta-
neously choose “ECP/SPP.”  By
choosing “ECP”, the onboard parallel
port will operate in ECP mode only.
Choosing “ECP/EPP” will allow the
onboard parallel port to support both

(3BCH/IRQ7)/
(278H/IRQ5)/
(378H/IRQ5)

SPP/(EPP/SPP)/
ECP(ECP/EPP)

Содержание MSI ATX TX5



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды