manualshive.com logo in svg

Premier Mounts PRF, Руководство по установке

Поделиться
Скачать
Premier Mounts PRF Скачать руководство пользователя страница 10

PRF

Page 10 

Installation Instructions

VESA 75/100 Installation

Step 1

Lift the fl at panel with the cover plate attached.

Place the mounting slot opening over the mounting tab 
(on the wall plate).

Slide the fl at panel down slowly, ensuring that the 
mounting slot is engaged by the mounting tab.

Step 2

Use a screwdriver to tighten the two (2) M6 x 12mm 
securing screws. 

This will lock the cover plate and wall plate securely 
together.

 

 

 Do not over-tighten these screws.

Locate the mounting points on the back of the fl at panel.

Secure the cover plate to the fl at panel using four (4) 
M4 x 10mm screws.

Step 1

  

The slotted opening must be facing up and the fl at 
surface touching the fl at panel surface.

 Do not over-tighten the mounting screws.

Cover Plate

Securing Screw
(Pre-Installed)

Mounting Point

Flat Panel

Slotted Opening

M4 x 10mm Screw

  

If you have a recessed VESA 75mm/100mm 
pattern or need more spacing between the wall 
and the fl at panel, use the appropriate number of 
universal spacers and corresponding length 
mounting hardware. If your mounting pattern is not 
75/100, proceed to page 11.

Attaching the Front Cover to the Wall Plate

Mounting
Slot

Mounting
Tab

Flat Panel

 Do not release the fl at panel until verifying the 

connection between the mounting slot and the 
mounting tab.

M6 x 12mm
Securing
Screw

Screwdriver

 

 If your fl at panel has a 200mm x 100mm or 
200mm x 200mm mounting pattern, the VESA 
Adapter Plate must be used. Please refer to the 
VESA Adapter Plate Pattern to determine the 
appropriate mount placement.

Содержание PRF














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды