Predator PREDATOR MAGNUM DJ150 Скачать руководство пользователя страница 41

035-19046-002-B-0104

Unitary Products Group

41

3.

Measure the time needed for one revolution of the hand 
on the smallest dial on the meter.  A typical gas meter 
has a 1/2 or a 1 cubic foot test dial.

4.

Using the number of seconds it takes for one revolution 
of the dial, calculate the cubic feet of gas consumed per 
hour.  (See example below). 

5.

If necessary, adjust the high pressure regulator as dis-
cussed in the section “Manifold Gas Pressure Adjust-
ment”. Be sure not to over-fire the furnace on Second 
stage. If in doubt, it is better to leave the Second stage of 
the furnace slightly under-fired. Repeat Steps 1-5.

To determine the rate of gas flow (First Stage)

1.

Turn of all other gas appliances connected to the gas 
meter.

2.

Turn on the furnace and make sure the thermostat is 
calling for first stage (60% input) heat.

3.

Even when the thermostat is calling for first stage heat, 
the unit will light on second stage and will run on Second 
stage for 1 minute.  Allow this one-minute time period to 
expire and be certain the unit is running on first stage.

4.

Measure the time needed for one revolution of the hand 
on the smallest dial on the meter.  A typical gas meter 
has a 1/2 or a 1 cubic foot test dial.

5.

Using the number of seconds it takes for one revolution 
of the dial, calculate the cubic feet of gas consumed per 
hour (See example below).

6.

If necessary, adjust the low pressure regulator as dis-
cussed in the section “Manifold Gas Pressure Adjust-
ment”. Be sure not to under-fire the furnace on first 
stage. If in doubt, it is better to leave the first stage of the 
furnace slightly over-fired (greater than 60% input). 
Repeat Steps 1-6.

NOTE:

To find the Btu input, multiply the number of cubic
feet of gas consumed per hour by the Btu content of
the gas in your particular locality (contact your gas
company for this information as it varies widely from
area to area).

TABLE 27: GAS RATE CUBIC FEET PER HOUR

Seconds

for One

Rev.

Size of Test Dial

1/2 cu. ft.

1 cu. ft.

10

180

360

12

150

300

14

129

257

16

113

225

18

100

200

20

90

180

22

82

164

24

75

150

26

69

138

28

64

129

30

60

120

32

56

113

34

53

106

36

50

100

38

47

95

40

45

90

42

43

86

44

41

82

46

39

78

48

37

75

50

36

72

52

35

69

54

34

67

56

32

64

58

31

62

60

30

60

Содержание PREDATOR MAGNUM DJ150





















































Отзывы: