background image

Page 15

For technical questions, please call 1-800-520-0882.

ITEM 69727 / 69730

Storage

When the equipment is to remain idle for longer than 

20 days, prepare the engine for storage as follows:
1. 

CLEANING

:

Wait for engine to cool, then clean engine with 

dry cloth.  

NOTICE:

  

Do not clean using water.

  

The water will gradually enter the engine 

and cause rust damage.  Apply a thin coat 

of rust preventive oil to all metal parts.

2. 

FUEL:

WARNING!

 

TO PREVENT SERIOUS 

INJURY FROM FIRE:

 

Drain the fuel tank in a well-ventilated area 

away from ignition sources.  If the engine is 

hot from use, shut the engine off and wait 

for it to cool before draining fuel. 

Do not smoke. 

a.  Place a funnel leading to a proper gasoline 

container below the carburetor.

b. 

Drain Plug

Sediment Cup

(some engines)

Remove the drain bolt from the bottom of the 

carburetor bowl and allow the fuel to drain.

c.  Remove the small sediment cup next to the bowl 

and allow the fuel to drain from there as well.

d.  Open the fuel valve.  After all fuel has 

drained, reinstall the drain bolt and sediment 

cup (if equipped).  Tighten securely.

3. 

LUBRICATION:

a.  Change engine oil.
b.  Clean out area around spark plug.  Remove 

spark plug and pour one tablespoon of engine 

oil into cylinder through spark plug hole.

c.  Replace spark plug, but leave spark 

plug cap disconnected.

d.  Pull Starter Handle to distribute oil in cylinder.  

Stop after one or two revolutions when you 

feel the piston start the compression stroke 

(when you start to feel resistance).

4. 

BATTERY: 

Disconnect battery cables (if equipped). 

Recharge batteries monthly while in storage.

5. 

STORAGE AREA: 

Cover and store in a dry, level, well-ventilated 

area out of reach of children.  Storage area 

should also be away from ignition sources, such 

as water heaters, clothes dryers, and furnaces.

6. 

AFTER STORAGE: 

Before starting the engine after storage, keep in 

mind that untreated gasoline will deteriorate quickly.  

Drain the fuel tank and change to fresh fuel if 

untreated gasoline has been sitting for a month, 

if treated gasoline has been sitting beyond 

the fuel stabilizer’s recommended time 

period, or if the engine does not start.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 69727

























Отзывы: