background image

Page 12

For technical questions, please call 1-800-520-0882.

ITEM 69727 / 69730

Maintenance

WARNING

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING: 

Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect 

the spark plug cap before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE: 

Do not use damaged equipment.  If abnormal noise, vibration, or excess 

smoking occurs, have the problem corrected before further use.
Follow all service instructions in this manual.  The engine may fail critically if not serviced properly.

Many maintenance procedures, including any not detailed in this manual, will need to be 

performed by a qualified technician for safety.  If you have any doubts about your ability to safely 

service the equipment or engine, have a qualified technician service the equipment instead.

Cleaning, Maintenance, and Lubrication Schedule

Note:

 This maintenance schedule is intended solely as a general guide.  If performance decreases or if 

equipment operates unusually, check systems immediately.  The maintenance needs of each piece of equipment 

will differ depending on factors such as duty cycle, temperature, air quality, fuel quality, and other factors.

Note:

 The following procedures are in addition to the regular checks and maintenance 

explained as part of the regular operation of the engine and equipment.

Procedure

Before 

Each Use

Monthly or 

every 20 

hr. of use

Every 3 mo. or 

50 hr. of use

Every 6 mo. or 

100 hr. of use 

Yearly or  

every 300 

hr. of use

Every 

2 Years

Brush off outside of engine
Check engine oil level
Check air cleaner
Check deposit cup
Change engine oil
Clean/replace air cleaner

*

Check and clean spark plug
1.  Check/adjust idle speed
2.  Check/adjust valve clearance
3.  Clean fuel tank, strainer 

and carburetor

4.  Clean carbon build-up from 

combustion chamber

**

**

Replace fuel line if necessary

**

*

Service more frequently when used in dusty areas.

**

These items should be serviced by a qualified technician.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 69727

























Отзывы: