Precor UBK13 Скачать руководство пользователя

Страница: 12 / 61

Page 10

Slightly loosen the three 4mm idler pulley bracket mounting bolts. The belt tension cannot be

adjusted if the idler pulley bracket mounting bolts are tightened.

Loosen the adjustment bolt lock nut.

Turn the adjustment bolt clockwise or counter clockwise as required until the gauge is in the range

of 70

5 pounds.

Remove and then replace the belt tension gauge on the primary drive belt. If the belt tension is out

range, repeat steps 5 and 6 until the belt tension is in range. If the belt tension is within range,

continue to the next step.

Tighten the three 4mm idler pulley bracket bolts. Note: Do not over tighten the bolts, if the bolts

are over tightened it is possible to damage the mounting hole threads of the generator. If by

chance the threads do become damaged, the idler pulley bracket can be removed and flipped

over 360 degrees and reinstalled. Doing this will allow the use of another set of mounting

holes on the generator.

Tighten the adjustment bolt lock nut.

Replace the covers.

Adjusting the Seat Carriage -

RBK Only

Perform this procedure if the front to rear movement of the seat is too tight or there is excessive side to

side seat wobble.

The end of the adjustment bolts are designed with two flat sides so that an open end wrench can

be used to rotate the bolt. Using a 10mm wrench on the adjust bolt, use a 22mm wrench to loosen

the two lock nuts on the left and right side just enough so the adjust bolt can be turned freely.

The seat carriage wheel is mounted on the adjustment bolt, which is offset. The offset bolt enables

the wheel to be tightened or loosened against the seat rail. Perform half of the adjustment using the

right hand adjustment bolt and half of the adjustment using the left hand adjustment bolt. Rotate

the adjust bolt counterclockwise until it just makes contact with the seat rail then turn it an

additional 1⁄8 turn. Hold the 10mm wrench at this position and firmly tighten the lock nut.

Содержание UBK13






























































Результаты поиска

Содержание UBK13

Отзывы:

Похожие инструкции для UBK13

Бренды по названию

Популярные бренды

Precor UBK13, Руководство по обслуживанию

Результаты поиска

Содержание UBK13

Отзывы:

Похожие инструкции для UBK13

Бренды по названию

Популярные бренды