Precor C532i Скачать руководство пользователя

Страница: 8 / 70

C532i, C556i Navy Elliptical Fitness Crosstrainer

Page 8

test or an

key to proceed to a different test.

26. The A/D number (incline position number) will be displayed as A/D XX. Press the CANCEL

key (532i) or the BACK key (C56i Navy) to proceed to the auto level test.

27. The test name “AUTO LEVEL” will be displayed. Press the OK key to enter the auto level

test or an

key to proceed to a different test.

28. The auto level incline position will be displayed, press an

key to change the auto level.

29. Press the CANCEL key (532i) or the BACK key (C56i Navy) to proceed to the battery test.

30. The test name “BATTERY” will be displayed. Press the OK key to enter the battery test or

key to proceed to a different test.

31. The battery voltage will be displayed as “XX.X VDC”.

32. Press the CANCEL key to return to the Display test or the RESET key to exit.

33. You may press the RESET key at anytime in the hardware validation program to exit the

hardware validation program.

Содержание C532i







































































Результаты поиска

Содержание C532i

Отзывы:

Похожие инструкции для C532i

Бренды по названию

Популярные бренды

Precor C532i, Руководство по обслуживанию

Результаты поиска

Содержание C532i

Отзывы:

Похожие инструкции для C532i

Бренды по названию

Популярные бренды