PRECITEC Lasermatic LightCutter Скачать руководство пользователя

Страница: 76 / 82

8.1 Basic technical information

LightCutter

8 - 66

D 159195

8.1.4

Running cables

(notes)

Follow the instructions below to set up the system and to find the cause for
any errors.

The basic rules below must be observed when fitting the cables.

When fitting cables, all movements relating to the specific application must be
observed

(max. displacement, max. rotation angle)

Avoid extreme robot hand rotation when teaching a process path.

Avoid any strain on cables and plug-in connections.

Cables must not be bent below the minimum bending radius specified in the
technical data sheet.

Cables must not be twisted in such a way that the maximum angle of twist
specified in the technical data sheet is exceeded.

Cables where no angle of twist is indicated must not be twisted.

Wind cables around rotating parts in such a way that the prescribed minimum
and maximum bending radii are observed and cables are not twisted.

Attention – Cables!

Use

only

original

Precitec

cables.

Unsuitable or wrongly assembled cables can have a negative effect on sensor
system functionality.

Not observing these notes may result in cables being destroyed or undesired
functions of the units connected to them.

Содержание Lasermatic LightCutter



















































































Результаты поиска

Содержание Lasermatic LightCutter

Отзывы:

Похожие инструкции для Lasermatic LightCutter

Бренды по названию

Популярные бренды

PRECITEC Lasermatic LightCutter, Руководство по эксплуатации

Результаты поиска

Содержание Lasermatic LightCutter

Отзывы:

Похожие инструкции для Lasermatic LightCutter

Бренды по названию

Популярные бренды