PRECITEC Lasermatic LightCutter Скачать руководство пользователя | Manualshive

Страница: 50 / 82

background image

5.1 Safety notes

5 - 40

© Precitec GmbH & Co. KG • EN 09/2019

5

Maintenance

5.1

Safety notes

General safety regulations

We assume that you know and observe the following generally accepted
safety regulations:

• VDE

Regulations, especially VDE 0100/ 0837

• BGV A1

General regulations

• BGV A3

Electrical systems and equipment

• BGV B2

Laser radiation accident prevention regulations

Personnel requirements

Any repair work and any work relating to troubleshooting require special
knowledge and must only be carried out by trained specialist staff. Precitec
shall not be liable for any damage caused by not complying with or having
insufficient knowledge about the information contained in the operating
instructions.

Specialist staff must be instructed in accordance with the regulations and
safety notes and informed of potentially hazardous situations.
In addition to this, the machine manufacturer's regulations must be observed.
The prescribed protective equipment must be used.

Precitec does not assume any liability for damage caused by improper
maintenance or improper intervention from unauthorised individuals.

Caution – Dangerous electrical voltage!

The system must be switched off and protected against being switched on
again before carrying out any maintenance or repair work on the laser head.

Caution – Danger of crushing!

During all maintenance and repair work, no hands or other body parts should
be in the proximity of the linear drive or under the laser head.

Caution – Laser beam!

The machine must be switched off before carrying out any maintenance or
repair work on the laser head. During commissioning the machine may operate
in

laser class 4

:

• Avoid radiation to eyes or skin caused by direct or scattered radiation.
• Do not look directly at the laser beam even using optical instruments.
• Use laser goggles complying with DIN EN 207 and BGV B2 that are

designed for the wavelength of the connected laser.

Attention – Sensitive optics!

Dust and firmly adhering dirt can lead to burn marks on the optics or damage
them. Therefore, only touch the non-sensitive parts on the optical components.

«
...
48
49
50
51
52
...
»

Содержание Lasermatic LightCutter



















































































Отзывы:

Нет отзывов

Похожие инструкции для Lasermatic LightCutter

Бренд: P.Lindberg Страницы: 86

Бренд: SIZZIX Страницы: 6

MS-3310, MS-4010, MS-4510

Бренд: Dolmar Страницы: 74

Бренд: Dolmar Страницы: 92

Бренд: Perfecta Страницы: 32

Бренд: Dremel Страницы: 4

Бренд: Dahle Страницы: 13

orbitalum GFX 3.0

Бренд: ITW Страницы: 318

Бренд: Olympia Страницы: 48

Excalibur Series

Бренд: Sawyer Страницы: 6

Бренд: EINHELL Страницы: 38

Бренд: EINHELL Страницы: 40

Бренд: EINHELL Страницы: 48

Бренд: EINHELL Страницы: 80

KBC-2600 SERIES

Бренд: SMC Networks Страницы: 10

Бренд: Danfoss Страницы: 60

Бренд: Zenoah Страницы: 20

Бренд: Zenoah Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды