Precision matthews PM-1127VFI-LB Скачать руководство пользователя страница 31

Страница: 31 / 34

Monthly maintenance (during build season)

• Check the lubrication of the sliding parts of the machine.

Apply oil if needed.

• Visually inspect the drive belts for excessive wear and

cracking. Check the belt tension by applying finger pressure
to each belt at a point midway between the two pulleys. For
correct tension a deflection of about ¼ to 3/8 of an inch
should be evident.

• Lubricate all points as required.

• Clean and coat the lead and feed screw with oil.

• Check all guards are secure and function correctly (includes

latches, locks, fasteners, and/or interlocks).

• Remove, clean, and re-saturated the wipers pads with oil

regularly. Wipers are designed to keep out small chips and
dirt between the slides and the ways.

• Check locking levers and adjusting handlers/levers for

smooth operation.

Содержание PM-1127VFI-LB



































Результаты поиска

Содержание PM-1127VFI-LB

Отзывы:

Похожие инструкции для PM-1127VFI-LB

Бренды по названию

Популярные бренды

Precision matthews PM-1127VFI-LB, Инструкция по безопасности и обучению

Результаты поиска

Содержание PM-1127VFI-LB

Отзывы:

Похожие инструкции для PM-1127VFI-LB

Бренды по названию

Популярные бренды