Pramac GA20000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

Pramac GA20000 Скачать руководство пользователя страница 22

General Information

16

Owner’s Manual for 50 Hz Air-Cooled Generator Sets

Replacement Parts

Accessories

NOTE:

Performance enhancing accessories are available for air-cooled generator sets. Contact an IASD or visit

https://www.pramac.com/gasresidential

for additional information on replacement parts and accessories.

Description

20 kVA

26R Exide battery

0H3421S

Spark plug

0G0767A (RC12YC or equivalent)

Oil filter

070185E

Air filter

0J8478

Control panel fuse

0D7178T

Accessory

Description

Cold Weather Accessories*—

•

Battery Pad Warmer

•

Oil Warmer

* each sold separately

•

Recommended in areas where temperatures fall below -18 °C (0 °F).

(Not necessary for use with AGM-style batteries)

•

Recommended in areas where temperatures fall below -18 °C (0 °F).

Scheduled Maintenance Kit

Includes all pieces necessary to perform maintenance on generator set along with
oil recommendations. See

http://www.pramacparts.com

for more information.

Fascia Base Wrap

The fascia base wrap snaps together around the bottom of the new air-cooled
generator sets. This offers a sleek, contoured appearance as well as offering
protection from rodents, reptiles, and insects by covering lifting holes in the base.
Requires use of mounting pad shipped with generator set.

Touch-Up Paint Kit

It is very important to maintain the look and integrity of the generator set enclosure.
This kit includes touch-up paint and instructions.

«
...
20
21
22
23
24
...
»

Содержание GA20000

















































Отзывы:

Нет отзывов