Pramac GA20000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

Pramac GA20000 Скачать руководство пользователя страница 19

General Information

Owner’s Manual for 50 Hz Air-Cooled Generator Sets

13

Specifications

Generator Set

Model

20 kVA

Rated voltage

400

Alternate voltage

380 / 416

Power factor

0.8

Rated maximum load current (amps) at rated voltage*

28.9

Maximum load current (amps) at alternate voltage*

30.1 / 27.18

Main circuit breaker

32 A

Phase

3

Rated AC frequency

50 Hz

Battery requirement

Group 26R, 12 Volts and 540CCA Minimum

(See

Replacement Parts

Enclosure

Aluminum

Weight (kg / lb)

207 / 457

A-Weighted sound pressure level (LpA) at 1 m (3.3 ft)

80 dB(A)

Sound pressure measurement uncertainty

1 dB(A)

A-Weighted sound power level (LwA)

94 dB(A)

Sound power measurement uncertainty

1 dB(A)

Normal operating range

This unit is tested in accordance to ISO 8528 standards
with an operating temperature of -29 °C (20 °F) to 50 °C
(122 °F). For areas where temperatures fall below 0 °C
(32 °F), a cold weather kit is recommended. There may
be a decrease in engine power when operated above
25 °C (77 °F). See engine specifications section.

These generator sets are rated in accordance with ISO 8528, Reciprocating Internal Combustion Engine Driven Alternating Current Generating
Sets–Safety.
* Natural gas ratings will depend on specific fuel joules (BTU) content. Typical derates are between 10–20% off the LP gas rating.

«
...
17
18
19
20
21
...
»

Содержание GA20000

















































Отзывы:

Нет отзывов