Pramac E5000, Руководство по эксплуатации и обслуживанию, Страница: 2 / 8

2
1. CONTENTS PAGE No
Safety instructions 2
Identification of components, controls and labels 2-4
Preliminary checks 5
Starting the generator 5
Using the generator 5
Stopping the generator 6
Maintenance 6
Transportation 6
Storage 6
Warranty 6
Trouble Shooting 7
Thank you for purchasing one of our generators. We would like to draw your attention to a few points concerning this manual:
- this manual gives useful guidelines for the correct use and maintenance of the generator set to which it refers: it is therefore essential
to pay full attention to all those paragraphs that illustrate the simplest and safest ways of using the generator.
- This manual is to be considered an integral part of the generator and must be included at the moment of purchase.
- This publication may not be reproduced, either totally or in part, without written authorization from the makers.
- All information shown hereafter is based on the data available at the moment of printing; the makers reserve the right to make
modifications to their products at any time, without warning and without incurring sanctions. You are therefore advised to check for
subsequent updatings frequently.
KEEP FOR FUTURE REFERENCE
USE OF THE GENERATOR
THIS GENERATING PLANT IS DESIGNED TO SUPPLY EITHER SINGLE PHASE OR THREE PHASE ELECTRICAL POWER.
NO OTHER APPLIANCES OTHER THAN THOSE INDICATED SHOULD BE USED.
2. GENERAL SAFETY INSTRUCTIONS:
ATTENTION: This manual contains operating and safety instructions which should be studied before using the generator. The
manufacturer will not accept liability for any damage or injury incurred through improper use.
WARNING: Treat the electrical output from the generator with the same caution as from the mains supply, electric shocks can
be fatal.
- Do not operate in enclosed areas, exhaust gasses are a health risk. In areas of poor ventilation the exhaust gasses must be extracted
or piped away from the work area. Operating in an enclosed area can also affect the performance of the engine due to restricted air
flow.
-
The generator must be operated on a level surface.
- The generator should be anchoured securely if there is a risk of movement.i.e units with unbraked chassis/frames should be
‘chocked’
- Do not replenish fuel or oil while the generator is running.
- Do not allow unauthorised persons or children in the work area, even after the machine has stopped there is a risk of severe burns
from hot parts of the machine.
- Maintenance or servicing should not be carried out with the machine running and only by experienced personnel.
- Where possible, ensure that the generator cannot be started by unauthorised persons (remove starter key or cover control panel etc.)
- Be familiar with how to turn off the machine quickly if necessary.
- Do not remove any protective devices or covers.
- The generator should be protected from heavy rain or snow.
- The machine does not need to be in a specially lighted area, however provide adequate lighting to comply with applicable working
norms.
- Do not use the machine in an explosive atmosphere.
- In the case of fire, use only an extinguisher suitable for electrical fires. ( a powder loaded fire extinguisher, etc.).
- Whenever it is necessary to work in close proximity to the machine, ear protection should be used (head muffs, ear plugs, etc.).
ATTENTION: Avoid any direct bodily contact with fuel, motor oil or battery acid. In case of contact with the skin wash with
soap and water and rinse thoroughly; do not use organic solvents. In case of contact with the eyes, rinse thoroughly with
water. In case of inhalation or swallowing, consult a medical practitioner.
3. IDENTIFICATION OF COMPONENTS AND CONTROLS:
E3200SHHPI / HG2500SHHPI SEE PICTURE NO.A
1 - THERMAL PROTECTION CIRCUIT BREAKER
2- SINGLE-PHASE SOCKET 110V 16A
3 – SINGLE PHASE SOCKET 220V 16A
4 – VOLTAGE CHANGEOVER SWITCH
E4000SHHPI SEE PICTURE Nos. B & D
1 - THERMAL PROTECTION CIRCUIT BREAKER
2- SINGLE-PHASE SOCKET 110V 16A
3 – SINGLE PHASE SOCKET 220V 16A
4 – VOLTAGE CHANGEOVER SWITCH
E5000SHHPI / E4000SHHPI-OP2/E6900SHHPI SEE PICTURE NO. B & C
1 - THERMAL PROTECTION CIRCUIT BREAKER
2- SINGLE-PHASE SOCKET 110V 16A
3 – SINGLE PHASE SOCKET 220V 16A
4 – VOLTAGE CHANGEOVER SWITCH
5 – SINGLE PHASE SOCKET 110V 32A