Powerware 1085 Series Скачать руководство пользователя страница 14

Страница: 14 / 54

Powerware 9350 Series 685 and 1085 Auxiliary Battery Cabinets

Installation Manual

164201408

Rev. P00 053002

FRONT

SIDE

FOAM

SUPPORT

JACKING

BOLT

(Step 2)

FLOOR

PROTECTOR

(Step 2)

LEFT HAND

DOOR

CUSHION

(Step 1)

(Step 3)

(Step 8)

Figure 5. Removing Front and Rear Supports

Loosen, but do not remove, the hardware holding the foam cushions to the front

and rear supports (labeled “1” in Figure 5).

WARNING: SERIOUS INJURY MAY OCCUR!

BATTERY CABINETS ARE EXTREMELY HEAVY. IF UNLOADING INSTRUCTIONS

ARE NOT CLOSELY FOLLOWED, CABINET MAY TIP.

Turn each jacking bolt consecutively, two full turns, until the foam cushions clear

the floor by approximately 3 mm (1/8 in.).

DANGER: RISK OF INSTABILITY!

TURNING THE JACKING BOLTS UNEVENLY MAY CAUSE THE CABINET TO

BECOME UNBALANCED. TO PREVENT TIPPING THE CABINET, RAISE AND

LOWER THE JACKING BOLTS EVENLY.

DANGER: CABINET MAY TIP!

THE BATTERY CABINET SHOULD ONLY BE RAISED APPROXIMATELY 3 mm

(1/8 in.) ABOVE THE FLOOR (JUST ENOUGH TO ALLOW REMOVAL OF THE

FOAM CUSHIONS).

After the foam cushions clear the floor, remove the hardware loosened in Step 3.

Pull the foam cushions out from under the battery cabinet. Please discard or

recycle them in a responsible manner.

Содержание 1085 Series























































Результаты поиска

Содержание 1085 Series

Отзывы:

Похожие инструкции для 1085 Series

Бренды по названию

Популярные бренды

Powerware 1085 Series, Руководство по установке

Результаты поиска

Содержание 1085 Series

Отзывы:

Похожие инструкции для 1085 Series

Бренды по названию

Популярные бренды