manualshive.com logo in svg

powersoft Duecanali 1604, Руководство по обслуживанию

Поделиться
Скачать
powersoft Duecanali 1604 Скачать руководство пользователя страница 7

QUATTROCANALI | SERVICE MANUAL

INDEX

4. Service Precautions

4.1 Notes on SOLDERING

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for the use with lead-free solders for repairs accompanied 
by reworking of soldering.
Do NOT use a soldering iron whose tip temperature cannot be controlled.

4.2 Notes on REPLACING PARTS

About the AMP Module

The amplifier module of this unit is able to correspond to repairing in the component manufacturer (Powersoft Company).
And it holds charge-free warranty period for 16 months after production.

4.3 Serial Number Labels

The details of the Serial Number Labels is as follows.

On the DSP Board

4.4 MAC Address Labels

The details of the MAC Address Labels are as follows.

On the Rear of the Amplifier

Inside the Base of the Amplifier (under the Flat Cable)

On the Top Cover of the Amplifier

Содержание Duecanali 1604





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды