background image

 

 

 

Never over fill fuel tank. 

 

 

Replace gasoline cap and tighten securely. 

 

 

If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 
minutes before starting the engine. 

 

 

Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. 
furnace, water heats, space heater, clothes dryer etc.). 

 

 

Allow machine to cool at least 5 minutes before storing. 

 

 

Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place 
containers on the ground away from your vehicle before filling. 

 

 

If possible, remove gas-powered equipment from the truck or trailer and refuel it on the ground. 

 

 

If this is not possible, then refuel such equipment on a trailer with a portable container, rather than 
from a gasoline dispenser nozzle. 

 

 

Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling 
is complete. Do not use a nozzle lock open device. 

 
 

OPERATION 

 

 

Do not put hands or feet near rotating parts, in the auger impeller housing or chute assembly. Contact 
with the rotating parts can amputate hands and feet. 

 

 

The auger (impeller) control lever is a safety device. Never bypass its operation. Doing so makes the 
machine unsafe and may cause personal injury. 

 

 

The control levers must operate easily in both directions and automatically return to the disengaged 
(vertical) position when released. 

 

 

Never operate with a missing or damaged chute assembly. Keep all safety devices in place and 
working. 

 

 

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, 
an odorless and deadly gas. 

 

 

Do not operate machine while under the influence of alcohol or drugs. 

 

 

Muffler and engine become hot and can cause burning. Do not touch. Keep children away. 

 

 

Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards 
or traffic. 

 

 

Exercise caution when changing direction and while operating on slopes. 

 

Содержание DB72024PA







































Отзывы: