background image

22 

www.powershield.com.au 

 

Symptom 

Possible cause 

Remedy 

Fault code is shown as 14 on LCD 
display and alarm is continuously 
sounding. 

The UPS shut down 
automatically because 
short circuit occurs on the 

UPS output. 

Check output wiring and if 
connected  devices  are  in 
short circuit status. 

Fault code is shown as 01, 02, 03, 
11, 12, 13 and 41 on LCD display 
and alarm is continuously 

sounding. 

A  UPS  internal  fault  has 
occurred.  There  are  two 
possible results: 

1. The load is still supplied, 
but directly from AC power 
via bypass.   

2.  The  load  is  no  longer 
supplied by power.   

Contact your dealer 

Battery backup time is shorter 
than nominal value. 

Batteries are not fully 
charged 

Charge the batteries for at 
least 5 hours and then 

check capacity. If the 
problem still persists, 
consult your dealer.   

Batteries defect 

Contact your dealer to 

replace the battery. 

Fault code is shown as 2A on LCD 

display and alarm is continuously 
sounding. 

The short circuit occurs on 

the charger output. 

Check if battery wiring of 

connected external pack is 
in short circuit status. 

Fault code is shown as 45 on LCD 
display. At the same time, alarm is 

continuously sounding. 

The charger does not have 
output and battery voltage 

is less than 10V/PC. 

Contact your dealer. 

 

5. Storage and Maintenance 

 
5-1. Operation   
The  UPS  system  contains  no  user-serviceable  parts.  Please  contact  your  dealer  if  the 
battery service life (3~5 years at 25°C ambient temperature) has been exceeded, as the 
batteries must be replaced.     

 
 

 
 

 

5-2. Storage   
Before storing, charge the UPS for 5 hours. Store the UPS covered and upright in a cool, 
dry location. During storage, recharge the battery in accordance with the following table:

 

Storage Temperature 

Recharge Frequency 

Charging Duration 

-10°C ~ 35°C 

Every 3 months 

1 hours 

@

5

~

35

 

-10°C ~ 25°C 

Every 6 months 

1 hours

@

5

~

25

 

 
 

Be sure to deliver the spent LiFePO4 (LiFe) battery to a recycling facility or ship 

it to your dealer in the replacement battery packing material.

 

Содержание Centurion RT PSLCERT1000


























Отзывы: