Powernail 445FS, Руководство по эксплуатации и обслуживанию

Страница: 5 / 16

5
to staple down fl ooring. Before storing the Stapler,
lubricate and cycle the Stapler in insure internal parts
are oil protected from corrosion.
WARNING: Detergent oil is not recommended and may
damage the seals.
TO LOAD MODEL 445FS:
Place two sticks (90 PowerStaples) into the Staple
Channel feed slot. Pull back the spring loaded Staple
Pusher over the staples until it contacts the last staple
and slowly release the Staple Pusher.
TO UNLOAD MODEL 445FS:
To remove staples from the Staple Channel, pull the two
round knobs on the Staple Pusher together. This will
clear it from the staple path. Then turn the Stapler over
so the staples slide out of the channel.
PARTS & SERVICE:
When ordering parts include the part number, part
description, PowerStapler model and serial number. Be
sure to state the quantity of the part(s) required. Contact
your Powerstaple Dealer for the necessary parts.
WARNING: Never work on the Stapler if the air line is
attached. Always disconnect the air line from the Stapler
fi rst.
Stapler DISASSEMBLY:
TO REPLACE RUBBER BUMPER (#20 or #65):
1. Disconnect the air supply
2. Remove the four (4) cap screws holding the Adapter
Foot, Foot and Staple Channel assembly to the main
Body (see illustration).
3. Pull the Rubber Bumper out of the cylinder bore.
Replace the old Bumper if it shows signs of wear or it is
split.
4. Reverse these steps to reassemble the Stapler. Be
sure to align the Driving Blade with the slot in the Staple
Channel Assembly while you reassemble the Stapler.
WARNING: It is not necessary to hit the Stapler hard
to activate it. Never hit the Stapler with excessive
force or with the metal end of the mallet, this will
damage the Stapler.
DO NOT USE THE METAL END OF THE MALLET
TO STRIKE THE PLUNGER, use the rubber capped
end only.
Never use the Safety Trigger interlock to lock up
the plunger and rack the wood with blows to the
Stapler body. This will severely damage the safety
mechanism and Stapler. This abuse and damage is
not covered by the warranty.
Before each use, check all screws to be sure they are
tight. Shock and vibration can loosen screws. Do not
over tighten any screw.
AIR SUPPLY:
The air must be clean and dry. Dirty and/or wet air will
damage the Stapler.
Drywall Dust:
• Using Pneumatic PowerStaplers in drywall dust
conditions will dramatically decrease the life of the
Stapler.
• Drywall dust is abrasive, when cycled through
the Stapler it will cause excessive wear.
The air source must continuously deliver 80 to 110
psi at 3-1/2 cubic feet of air per minute to operate
the Stapler. For operation, connect a 1/4” minimum
internal diameter and clean air hose to the Stapler.
Be sure the air regulator is set at 90 psi. If the staple
is not countersunk below the surface of the wood, turn
up the air pressure, but not over 110 psi.
Check for air supply leaks that waste air and starve
the Stapler of air thereby reducing its performance.
There should be no orifi ce smaller than 1/4” in the air
path between the Regulator and the Stapler.
LUBRICATION:
You must lubricate the Stapler manually. The
frequency of lubrication is dependent upon the duty
cycle of the Stapler. Continuous duty requires more
frequent oiling than intermittent duty.
At least every eight (8) hours place two to four drops
of Air Tool Oil, supplied with your Stapler, into the
disconnected air line male connector attached to the
Stapler.
WARNING: Do not over lubricate the Stapler, excess
oil mist or drops will be vented with spent air when
over lubricated. Excess oil could stain the wood
fl ooring, walls or furnishings. Dry fi re the Stapler,
without staples, to purge excess oil, before you begin
OPERATING INSTRUCTIONS, continued