background image

 

 

www.powermaxfitness.net 

12 

Translation of Error Codes 

Error 
Code 

Description 

Solution 

E1 

Communication Abnormal:

 

when the power is on, the 
connection between lower 
controller and the console is 
abnormal. 

Possible Cause: 

The communication between the lower controller and 
console is blocked, check each joint between the 
controller and console, ensure that each core is fully 
plugged in. 

Check the connection line, replace it if it’s damaged.

 

E2 

No signal from motor. 

Possible Cause: 

Check the motor cable to see whether it is connected 
well or not, if not, connect the motor wire again. 
Check the motor cable to see whether it is damaged 
or has a burnt smell, if yes, replace the motor. 
Check the speed sensor to see whether it is correctly 
installed or damaged. 

E5 

Over current protection: 

In working, the lower controller 
detects the current to be over 6A 
for more than 3 seconds. 

Possible Cause: 

Overloading leads to excessive current, and the 
system stop out of self-protection, or some part is 
stuck, causing the motor to stop. 
Adjust the treadmill and restart it. 
Check if there is liquid or burnt smell while the motor 
is running, if yes, replace the motor. 
Check if the controller has a burned smell, if yes, 
replace the controller. 
Check the power supply voltage, if it does not match 
the specifications, change into correct voltage and 
test the machine again. 

E6 

Explosion-proof impact protection: 

The abnormal voltage or motor 
cause the faulty of circuit that 
drive the motor. 

Possible Cause: 

Check if the power supply voltage is 50% lower than 
normal voltage. 
use the correct voltage and test the machine again. 
check if the controller has a burnt smell and replace 
the controller. 
Check if the motor cable is connected and connect 
the motor wire again. 

E7 

No safety key 

Put the safety key on the right place. 

Содержание TDM-98















Отзывы: