Powermax Tech AHE58-55 Скачать руководство пользователя

Страница: 5 / 16

第 5 页共 16 页

Appearance

Description

Stitch compensation key

：

Start stitch compensation if press, stop stitch compensation if loose.

Trimming key

：

Select/Cancel automatic trimming. The trimming status is displayed on top of LCD

screen. Detailed see "3.1.5 trimming set.

Press foot lifting key:

Every effective pushed the key once; round with trimming after press foot

lifting, sewing end press foot lifting and manual press foot lifting. The current status is displayed

on top of LCD screen. Detailed see "3.1.4 press foot lifting set.

One-Shot-Sewing key

：

Select/Cancel one-Shot-Sewing, it is effective only into

multi-segment

sewing mode, when chose one-shot sewing, one-shot foot pedal can complete one needle of

multi-segment sewing

；

The one-shot-sewing status is displayed on top of LCD screen. Detailed

see "3.1.6 trigger set.

3 System Parameter Setting Description

3.1 Operator Mode

In this mode, various sewing modes are available after technical parameters settings. As the

default setting, the system enters this mode when it starts. Under this mode, such basic

functions as normal sewing work and modes change can be realized but no change inside

parameters and setting.

：

During working, if long time without press button, HMI will change to idle status

automatically, and will cancel the operation before.

3.1.1 Sewing Mode Setup

Free sewing mode

:Press

key, free sewing mode icon

is lightened in LCD area. LCD

indicates free sewing mode has been selected; it is ready just step the pedal for

operation.

Multi-segment sewing mode

Press

key, constant-stitch sewing icon

is lightened

in LCD area. LCD

is multi-segment sewing status

。

Use

keys

and

keys to choice the N segment, and press

key to entry multi-segment

sewing stitch number of each segment setup status

. You may use

keys

and

keys

to choice the need to modify number of segment, use

keys

and

keys to modify number of needle in multi-segment sewing stitch setup status.

W sewing mode

: Press

key, constant-stitch sewing icon

is lightened in LCD area.

Содержание AHE58-55

















Результаты поиска

Содержание AHE58-55

Отзывы:

Похожие инструкции для AHE58-55

Бренды по названию

Популярные бренды

Powermax Tech AHE58-55, Инструкция по эксплуатации

Результаты поиска

Содержание AHE58-55

Отзывы:

Похожие инструкции для AHE58-55

Бренды по названию

Популярные бренды