Powermatic 201 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 40

background image

7

SPECIFICATIONS: Model 201, 22” Planer

Table with standard extensions........................................................................................................................ 28” x 38”
Maximum cutting width ............................................................................................................................................. 22"
Maximum thickness ................................................................................................................................................. 1/4"
Full width depth of cut............................................................................................................................................ 3/16"
Minimum planing length............................................................................................................................................ 10"
Number of knives ........................................................................................................................................................ 4
Cutterhead speed ..........................................................................................................................................4800 RPM
Cuts per minute ...................................................................................................................................................19,200
Cutterhead diameter ............................................................................................................................................. 3-1/4"
Blade size ............................................................................................................................22-1/8" L x 7/8" W x 1/8" T
Feed rate...................................................................................................................................................20 & 30 FPM
Overall dimensions................................................................................................................ 32-1/4" W x 50" H x 50" L
Motor ......................................................................... 7.5 HP, 3 Ph, 230V or 7.5 HP, 3 Ph, 460V or 7.5 HP, 1 Ph, 230V
Shipping weight .............................................................................................................................................. 1,197 lbs.

NOTE: The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Powermatic reserves the right to change specifications without notice and without
incurring obligations.

«
...
5
6
7
8
9
...
»

Содержание 201









































Отзывы:

Нет отзывов

Похожие инструкции для 201

Бренд: Makita Страницы: 4

Бренд: Onkyo Страницы: 32

Бренд: NAD Страницы: 11

Бренд: Denver Страницы: 50

Бренд: King Industrial Страницы: 13

Бренд: YATO Страницы: 112

Бренд: Emerson Страницы: 19

Бренд: Naxa Страницы: 5

Бренд: Pyle Страницы: 4

Бренд: SOUNDMASTER Страницы: 5

Бренд: NAD Страницы: 14

Бренд: Zenith Страницы: 47

Бренд: Magnat Audio Страницы: 36

Бренд: Makita Страницы: 10

Бренд: Samsung Страницы: 167

Бренд: Yamaha Страницы: 108

Бренд: Optimus Страницы: 32

P47DH - DEH Radio / CD Player

Бренд: Pioneer Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды