Powermatic 201 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 40

background image

6

Familiarize yourself with the following safety notices used in this manual:

!

CAUTION: (This means that if precautions are not heeded, it may result in minor or moderate injury

and/or possible machine damage)

!

WARNING: (This means that if precautions are not heeded, it could result in serious injury or

possibly even death).

!

SAFETY

Familiarize yourself with the location and content of this decal on your machine.

!

1.       Read instruction manual before operating machine.
2.       Do not operate without all guards properly installed.
3.    Remove or fasten loose articles of clothing such as neckties, etc.
   Contain long hair.
4.       Remove jewelry such as finger rings, watches, bracelets, etc.
5.    Use approved safety glasses and/or face shield to protect eyes, and
             use other personal safety equipment as required.   Do not wear
   gloves.

6.       Disconnect machine from power source before making any
             adjustments or cleaning chips away from machine.
7.       Keep the floor around machine clean and free from scraps,
             sawdust, oil and grease to minimize the danger of slipping.
8.       Do not operate this machine while under the influence of alcohol
   or drugs.
9.       Failure to comply with these warnings may result in serious
   personal injury.

DO NOT REMOVE OR OBSCURE THIS LABEL

«
...
4
5
6
7
8
...
»

Содержание 201









































Отзывы:

Нет отзывов

Похожие инструкции для 201

Бренд: Teac Страницы: 16

Бренд: Luxman Страницы: 48

Бренд: Blaupunkt Страницы: 9

Бренд: Teac Страницы: 1

Бренд: Teac Страницы: 100

Mini Land Planer

Бренд: Erskine Attachments Страницы: 19

Бренд: LEXIBOOK Страницы: 54

Бренд: Xiron Страницы: 8

Бренд: NAD Страницы: 45

Бренд: Onix Страницы: 24

Бренд: Hamilton/Buhl Страницы: 12

AZ7261 - Cd Personal

Бренд: Magnavox Страницы: 29

Бренд: Jensen Страницы: 8

Бренд: LaserDisc Страницы: 32

Бренд: Luxman Страницы: 6

Бренд: Yamaha Страницы: 20

Бренд: NEC Страницы: 7

Бренд: RCA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды