background image

 

26.  Do not use this dust collector with a damaged 

cord or plug. If the unit is not working as it 
should, has been dropped, damaged, left 
outdoors, or dropped into water, return it to a 
service center. 

27. Do not unplug by pulling on cord. To unplug, 

grasp the plug, not the cord. 

28. Do not use without dust bag and/or filters in 

place. 

29.  Do not handle plug or machine with wet hands. 

30.  Do not put any objects into the openings. Do not 

use with any opening blocked; keep free of 
dust, lint, hair, and anything that may reduce air 
flow. 

31.  Do not operate without hose connected to the 

inlet. Place cap on unused inlet port. Hazardous 
moving parts inside. Unplug before removing or 
connecting inlet or inlet guard. 

32. Use recommended accessories; improper 

accessories may be hazardous. 

33.  Maintain tools with care. Follow instructions for 

lubricating and changing accessories. 

34. Turn off machine and disconnect from power 

before cleaning. Use a brush or compressed air 
to remove chips or debris; do not use bare 
hands. 

35.  Do not leave the machine when it is plugged in. 

Unplug from outlet when not in use and before 
servicing. 

36. Do not stand on the machine. Serious injury 

could occur if the machine tips over. 

37. Use proper extension cord. Make sure your 

extension cord is in good condition. When using 
an extension cord, use one heavy enough to 
carry the current your product will draw. An 
undersized cord will cause a drop in line voltage 
resulting in loss of power and overheating. 

Sect. 

6.2,

 Table 2 shows correct size to use 

depending upon cord length and nameplate 
ampere rating. If in doubt, use the next heavier 
gauge. The smaller the gauge number, the 
heavier the cord. 

38. The dust collector is intended for household 

use. 

 

 

 

 

Familiarize yourself with the following safety notices used in this manual: 

 This means that if precautions are not heeded, it may result in minor injury and/or possible 

machine damage. 

 This means that if precautions are not heeded, it may result in serious, or possibly even fatal, 

injury. 

 

SAVE THESE INSTRUCTIONS 

  

 

 

 

 

 

WARNING:

 This product can expose you to 

chemicals including lead which is known to the 
State of California to cause cancer and birth 
defects or other reproductive harm. For more 
information go to http://www.p65warnings.ca. 
gov. 

 

WARNING:

 Drilling, sawing, sanding or 

machining wood products generates wood dust 
and other substances known to the State of 
California to cause cancer. Avoid inhaling dust 
generated from wood products or use a dust 
mask or other safeguards for personal 
protection. 

Wood products emit chemicals known to the 
State of California to cause birth defects or other 
reproductive harm. For more information go to 
http://www.p65warnings.ca.gov/wood. 

Содержание 1792205HK

























Отзывы: