background image

 12 

The conductor with insulation having an outer 
surface that is green with or without yellow stripes is 
the equipment-grounding conductor.  

If repair or replacement of the electric cord or is 
necessary, do not connect the equipment-grounding 
conductor to a live terminal. 

Use only 3-wire extension cords that have 3-prong 
grounding plugs and 3-pole receptacles. 

Repair or replace damaged or worn cord 
immediately. 

6.2

  Extension cords 

The use of extension cords is discouraged; try to 
position machines near the power source. If an 
extension cord is necessary, make sure it is in good 
condition. When using an extension cord, be sure to 
use one heavy enough to carry the current your 
product will draw. An undersized cord will cause a 
drop in line voltage resulting in loss of power and 
overheating. Table 2 shows correct size to use 
depending on cord length and nameplate ampere 
rating. If in doubt, use the next heavier gauge. The 
smaller the gauge number, the heavier the cord. 

Amp Rating  Volts  Total length of cord in feet 

More 
Than 

Not 
More 
Than 

240 50 100 200 

300 

 AWG 

0 6 

  18 

16  16  14 

6 10 

  18 

16  14 

12 

10 12 

 

16 

16  14 

12 

12 16 

 

14 

12 

Not 

Recommended 

 

Table 2:  Extension cord recommendations 

7.0

  Operations 

7.1

 Start/stop 

Power Indicator Light

 – The start switch has a 

power indicator lamp which is on 

whenever there is 

power connected

 to the collector, not just when the 

machine is running. Do not assume that no light 
means there is no power to the machine. If the bulb 
is bad, there will be no indication. Always check 
before use. 

 Do not rely that no light means 

no power to the machine. Always check for 
power first. Failure to comply may cause serious 
injury! 

Refer to Figure 16: 

Start (A)

 – Press the green start switch.  

When power is connected to the machine, the green 
light is always on regardless of whether the collector 
is running or not. 

Stop (B)

 – Press the red switch to stop. 

Reset

 – If the dust collector stops without pressing 

the stop button, as the result of a tripped fuse or 
circuit breaker: 

1.  Press red button (C) to reset.  

2.  Press green button (A) to restart machine. 

 

Figure 7-1 

7.2

  Safety Key 

The start/stop switch comes equipped with a 
magnetic safety key. See Figure 16. When in place 
on the switch, the magnetic safety key trips a relay 
which allows the machine to start and stop when the 
respective switches are pressed. Being magnetic, 
the safety key can be removed to make the machine 
inoperable. 

When using the machine, place the key on the 
switch cover lining up the arrow on the key with the 
REMOVE arrow on the cover. Then rotate the key 
so the arrow lines up with the LOCK arrow. This 
prevents the safety key from vibrating loose when 
the machine is operating.  

7.3

 Remote controller 

The RF (radio frequency) remote controller operates 
on 2 AAA batteries (included). The batteries will 
need replacing periodically. The remote controller 
has an effective range up to approximately 50 feet 
(15 meters). 

Press the 

+

 or 

 button to select desired timer 

setting: 2, 4, 6 or 8 hours. The dust collector will stop 
automatically at end of selected period. For 
continuous operation (no timer) select infinity (

4

position. 

 

Figure 7-2 

 

Содержание 1792205HK

























Отзывы: