Powerhouse M46850E.1 Скачать руководство пользователя страница 3

Страница: 3 / 30

Machine Component Identification

Engine -

Engine is NOT shipped with oil. Refer to engine owners’ manual for proper viscosity and capacity of oil

for your engine.

On/Off Switch -

Make sure switch is at “ON” position when starting engine.

Compressor Air Filter -

Make sure your air filter is clean and particle free. See pump exploded view for

replacement filter part number.

Belt Guard

- Covers the belt, motor pulley and flywheel.

NEVER

operate compressor without belt guard.

Regulated Pressure Gauge

- Easy to read liquid filled gauge indicates regulated pressure.

Port at Tank Pressure

– To access full tank pressure, attach hose to this port. Thread size is ¼” NPT.

Tank Drain

– Location of tank drains. Drain tank daily or after each use.

Regulator

– Adjust outlet pressure, not to exceed pressure rating of the tool.

Quick Connect

This is a ¼” quick connect.

10.

Unloader

- Lift knob to relieve pressure when starting the engine.

11.

ASME Safety Valve

- This valve automatically releases air if the tank pressure exceeds the preset maximum.

12.

Pneumatic Tire -

Keep tire pressure at 20 psi for easy movement.

13.

Tank Pressure Gauge

- Easy to read liquid filled gauge indicates pressure in the tank.

14.

Discharge Tube

- This tube carries compressed air from the pump to the check valve. This tube becomes very

hot during use. To avoid the risk of severe burns, never touch the discharge tube.

15.

Engine Control

- Location of choke, engine speed and fuel valve.

Содержание M46850E.1































Результаты поиска

Содержание M46850E.1

Отзывы:

Бренды по названию

Популярные бренды

Powerhouse M46850E.1, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание M46850E.1

Отзывы:

Бренды по названию

Популярные бренды