background image

Splitting Operation 

 

22 

SPLIT CONTROL LEVER OPERATION

 

     

WARNING:

  NEVER

 attempt to remove a stuck log by: 

• 

Modifying the splitter. 

• 

Adding attachments to the splitter. 

Personal injury could result from log or metal pieces flying out at high speed toward the 
operator or bystanders, or the splitter could become damaged. 

 

9.  Return 

wedge 

Move Split Control Lever away from end plate to return wedge

 

Once the control valve is actuated in the return direction, the wedge is designed to keep returning 
by itself completely and then stop automatically.   
 

 

 
 
 
 
 

WARNING:

  

Stay clear while the wedge is returning.  It is still powerful enough on the return stroke to 
cause serious injury. 

 

10.  Remove split 

wood 

Remove split wood from area. 

 

     Move each log away from log splitter after it is split. Split logs left near the log splitter are a trip 

hazard. 

 

11.  After use 

1.  Turn off engine. 

2.  Remove engine debris

.

   

Debris on a hot engine can be a fire hazard.  After the engine is off, clean debris and chaff from 
engine cylinder head, cylinder head fins, blower housing rotating screen, and muffler areas.    

 

WARNING:

 

Avoid contact with hot muffler. 

3.  Return to horizontal position

.

   

If in the vertical position, return log splitter to the horizontal position for greater stability and 
to prepare for transportation.  Avoid contact with hot muffler. 

 

 

Содержание M1165E













































Отзывы: