PowerBass ASA 1100.5x Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 24

background image

TECHNICAL FEATURES

•

Low Profile Aluminum Finned Heatsink

•

PWM MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads

•

Variable High Pass and Low Pass Electronic Crossover

•

Soft Delay Remote Turn On/Off Circuit to Eliminating Pops and Clicks

•

Fully Adjustable Bass EQ at 40Hz (18dB)

•

Self Diagnostic Multi Protection Circuit with LED Status Indicator for; Impedance Over-load, Speaker
Short Circuit, Thermal Overheating, and DC Output.

•

2-ohm Stereo Stable (4-ohm Mono Bridgeable)

•

Custom Tooled Speaker and Power Terminal Blocks

•

Variable Gain Control

•

Gain Control Port (for Optional Remote Control - model ASA-BASS sold separately)

•

Low Level Line Inputs and Outputs

INSTALLATION EXPERIENCE

Installation of PowerBass mobile amplifiers requires detailed knowledge of electronics wiring and proper
speaker impedance. We strongly recommend installation by an authorized PowerBass dealer. This Own-
ers Manual only provides general installation and operation instructions. If you have any reservations
about your installation skills, please contact your local PowerBass dealer for assistance.

IMPORTANT : This amplifier is designed for operation in vehicles with 12-volt Negative ground
electrical systems only.

PREPARING FOR INSTALLATION

NOTE: The tools listed below may be required for basic installation

•

An electric drill with bits

•

Philips head and standard screwdrivers

•

Wire strippers

•

Crimping tool

•

VOM (electronic volt ohm meter)

•

Heat shrink tubing and heat gun

•

Soldering iron

•

Electronic (not Acid Core) Solder

3

«
1
2
3
4
5
...
»

Содержание ASA 1100.5x

























Отзывы:

Нет отзывов

Похожие инструкции для ASA 1100.5x

PresentationPro PA300 Plus

Бренд: Califone Страницы: 11

Бренд: Tube Amp Manufactur Страницы: 5

Бренд: Cable-Tronix Страницы: 5

XXRK-630SP4-14SG-ST4

Бренд: J&M Corporation Страницы: 9

Бренд: Vitus Audio Страницы: 4

Бренд: Marantz Страницы: 10

Бренд: Audiovox Страницы: 17

Бренд: B2 Audio Страницы: 10

Бренд: AvidHiFi Страницы: 16

Бренд: Oldfield Amplifiers Страницы: 11

Бренд: NAD Страницы: 5

Бренд: SPHINX Страницы: 42

Бренд: Crate Страницы: 8

Бренд: AXTON Страницы: 58

Бренд: Pro'sKit Страницы: 20

Delta Audiophile AP2496

Бренд: M-Audio Страницы: 46

Бренд: Harley Benton Страницы: 8

Бренд: Legacy Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды