manualshive.com logo in svg

Power integrations Scale-2 1SC0450E2B0, Руководство по применению, Страница: 9 / 25

Поделиться
Скачать
Power integrations Scale-2 1SC0450E2B0 Скачать руководство пользователя страница 9

SCALE™-2 1SC0450E2B0 

   

 

Preliminary Description & Application Manual 

 

www.power.com/igbt-driver 

Page 9 

GND 

Both  ground  pins  must  be  connected  together  with  low  parasitic  inductance.  A  common  ground  plane  is 
strongly recommended. Furthermore it is recommended to shield all primary-side circuitry with the ground 

plane. The connecting distance between the ground pins must be kept to a minimum. 

SO (status output) 

When  no  primary-side  under-voltage  condition  is  detected,  an  internal  pull-up  resistor  of  10kΩ  keeps  the 
output level at the voltage level of VCC. When a primary-side supply under-voltage is detected, the status 

output SO goes to low (connected to GND). The SO output is automatically reset (returning to the voltage 
level of VCC) when the under-voltage on the primary side disappears. 
The maximum SO current in a fault condition must not exceed the value specified in the driver data sheet 
/3/. 

Recommended Interface Circuitry for the Secondary Side Connectors 

Pins 6 to 16 

 

Fig. 6 

Recommended  user  interface  of  the  1SC0450E2B0  (secondary-side  pins  6  to  16)  without  gate 

boosting (refer to chapter “Gate Boosting” and Fig. 11 for gate-boosting circuitry) 

 

Содержание Scale-2 1SC0450E2B0


























Отзывы:

Нет отзывов