Power integrations Scale-2 1SC0450E2B0 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 25

Power integrations Scale-2 1SC0450E2B0 Скачать руководство пользователя страница 4

SCALE™-2 1SC0450E2B0

Preliminary Description & Application Manual

www.power.com/igbt-driver

Page 4

Driver Overview

The 1SC0450E2B0 is a driver core equipped with the latest SCALE-2 chipset from Power Integrations /1/.
The SCALE-2 chipset comprises a set of application-specific integrated circuits (ASICs) that cover the main

functions needed to design intelligent gate drivers. The SCALE-2 driver chipset is a further development of
the proven SCALE™-1 technology /2/.
The 1SC0450E2B0 targets medium- and high-power IGBT applications up to 6500V. The driver supports
switching frequencies up to 10kHz with best-in-class efficiency. The 1SC0450E2B0 comprises a complete
single-channel IGBT driver core, fully equipped with an isolated DC/DC converter, electrical interface for the

external use of fiber-optic transceivers, short-circuit protection, Advanced Active Clamping and supply-
voltage monitoring. Additional features such as gate boosting are also implemented and provide further
driving benefits.

Fig. 2

Block diagram of the 1SC0450E2B0 driver core

«
...
2
3
4
5
6
...
»

Содержание Scale-2 1SC0450E2B0


























Отзывы:

Нет отзывов