Power integrations Scale-2 1SC0450E2B0 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 25

Power integrations Scale-2 1SC0450E2B0 Скачать руководство пользователя страница 10

SCALE™-2 1SC0450E2B0

Preliminary Description & Application Manual

www.power.com/igbt-driver

Page 10

Pins 17 to 32

Fig. 7

Recommended command interface circuitry with Avago fiber-optic links HFBR-x522ETZ

Description of Secondary-Side Interfaces

General

The driver’s secondary side is equipped with an 11-pin and two 8-pin interface connectors.
The 11-pin interface connector features the following terminals:



1x DC/DC output terminal VISO



1x emitter terminal VE



1x secondary-side ground COM



1x collector sense terminal VCE



1x reference terminal REF for short-circuit protection



1x input terminal CSHD to set the turn-off delay after fault



1x active clamping terminal ACL



1x turn-on gate terminal GH



1x turn-off gate terminal GL



1x gate-boosting power supply VGB



1x gate-boosting signal GBS

The two 8-pin interface connectors combine the command interface and feature the following terminals:



1x DC/DC output terminal VISO



11x secondary-side ground COM



1x PWM input (inverted)



3x status feedback input/output (inverted)

All inputs and outputs are ESD-protected.

«
...
8
9
10
11
12
...
»

Содержание Scale-2 1SC0450E2B0


























Отзывы:

Нет отзывов