Powercraft
09
15. Disconnect tools.
When not in use, before servicing and when changing accessories such as blades, bits
and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting wrenches are removed from tool
before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be sure switch is off when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords intended for use outdoors and so
marked. Always use tool in conjunction with a residual circuit breaker device.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service centre unless otherwise indicated elsewhere in this instructions
manual. Have defective switches replaced by an authorized centre. Do not use tool if
switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than recommended in this
operation instructions or the catalogue may present a risk of personal injury.
22. Have your tool repaired by an expert.
This appliance is manufactured to very high standards and meets relevant safety
regulations. Repairs should only be done by a suitable qualified electrical engineer or
otherwise.
23. Hearing protection should be worn.
Electrical safety
Always check that the power supply corresponds to the voltage on the rating plate.
Your machine is double insulated in accordance with EN 50144; therefore no
earthwire is required.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The
minimum conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel
completely.
• When the mains cord is damaged, it has to be replaced by an authorized repair centre,
to prevent dangerous situations.
• Always keep the cord away from the moving parts of the machine.
• In the case of locking, switch the machine off immediately and remove the plug from the mains.
UK
08
Powercraft
General safety instructions
Attention! When using electric machines always observe the safety regulations applicable in
your country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions and also the enclosed safety instructions.Keep these instructions in a safe
place!
1.
Keep work area clear.
Cluttered areas and benches invite injuries.
2.
Consider work area environment.
Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep
work area well lit. Do not use power tools in presence of flammable liquids or gases.
3.
Guard against electric shock.
Prevent body contact with grounded surfaces (e.g. pipes, radiators, refrigerators).
4.
Keep visitors away.
Visitors should be kept away from the work area at all times. Do not let visitors handle the
Combitool at any time.
5.
Store unused tools.
When not in use keep tools out of reach of children. Store in a dry and secure location.
6.
Do not force tool.
Do not apply undue pressure as this may affect performance and may cause damage to
the machine. Forcing the job also increases the potential for accidents.
7.
Use right tool.
Do not force small tools or attachments to do the job of heavy duty tool. Do not use a tool
for purposes not intended.
8. Dress
properly.
Do not wear loose clothing or jewellery. They can be caught in moving parts. Rubber
gloves and nonskid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
9.
Use safety glasses.
Also use face or dust mask when operation is dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust extraction and collection facilities
ensure these are connected and properly used.
11. Do not abuse cord.
Never carry tool by cord or yank it to disconnect it from electrical socket. Keep cord from
heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold work. It's safer than using your hand and it frees both hands
to operate tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep tools sharp and clean for better and safer performance. Follow instructions for
lubricating and changing accessories. Inspect tool cords periodically and, if damaged,
have repaired by authorized service facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free from oil and grease.
UK