manualshive.com logo in svg

Poulan Pro Pro 925 ZX, Pro 950 ZX, Руководство оператора

Поделиться
Скачать
Poulan Pro Pro 925 ZX, Pro 950 ZX Скачать руководство пользователя страница 53

English-

51

LUBRICATION

Lubrication

Lubrication Schedule 

General

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oil can, it must be filled with engine oil.

When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulfide grease.

For daily use, the machine shall be lubricated twice weekly.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this 
happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. 
Gasoline or other petroleum products must not be used to clean belts.

8011-673

Lubrication schedule

Lubricate with grease gun

Oil change

Filter change

Lubricate with oil can

Level check

12/12 Every year

1/52 Every Week

1/365 Every day

Содержание Pro 925 ZX, Pro 950 ZX

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды