background image

31

Debris 

shield

Drive 
belt

Belt 

retainers

SERVICE AND ADJUSTMENTS

Debris 

shield

Belt retainer

Belt 
keepers

Drive 
belt

Slot

Tab

TO REPLACE DRIVE BELT
1.  Place new drive belt in the belt retainer 

of the debris shield.  Be sure to route 
belt between belt keepers and through 
slot as shown. 

18" (45cm) HI-VAC MODELS:

21" (53cm) HI-VAC MODELS:

2.  Route the other end of the new drive 

belt through hole in housing.

3.  Reattach debris shield to housing with 

screw previously removed.  Be sure 
tab of debris shield is in gap of hous-
ing.

4.  Position blade on the blade adapter 

aligning the two (2) holes in the blade 
with the raised lugs on the adapter.

5.  Be sure the trailing edge of blade (op-

posite sharp edge) is up toward the 
engine as shown.

6.  Install the blade bolt with the lock 

washer and hardened washer into 
blade adapter and crankshaft.

7.  Use block of wood between blade and 

lawn mower housing and tighten the 
blade bolt, turning clockwise.

•  The recommended tightening torque is 

35–40 ft. lbs.  

IMPORTANT

:  Blade bolt is grade 8 heat 

treated. 
8.  Return mower to upright position.
9.  Install new drive belt into idler arm as-

sembly, then around the drive pulley.  
Be sure belt is inside of belt keepers.

NOTE:

 Pulling on the drive belt (to install 

it on the drive pulley) will cause the other 
end of the belt to free itself from the debris 
shield retainer and come into contact with 
the pulley end of the blade adapter.
10. Reattach drive cable and return spring 

to the idler arm assembly, then reat-
tach drive cable to anchor.

11. Reattach drive cover with screws previ-

ously removed.

12. Connect spark plug wire to spark plug.

22PLUS REAR WHEEL DRIVE MODELS: 
1.  Remove screws securing rear baffle.
2.  Turn lawn mower on its side with air 

filter and car bu re tor down.

NOTE

:  Before tipping lawn mower to 

remove drive belt, empty fuel tank by run-
ning engine until fuel tank is empty.
3.  Remove rear baffle from mower.

Blade 

bolt

Hardened washer

Lockwasher

Blade 
adapter

Blade

Belt 

retainer

Gearcase 

belt keeper

Debris 
shield

Rear 
baffle

Gearcase 
pulley

Содержание PR625Y22RHP





































Отзывы: