background image

14

SNOW THROWER

Always observe the safety rules when performing any 

main te nance.

TIRES

• 

Maintain proper air pressure in both tires (14–17 P.S.I. 

/ 19-24.5 N-m).

•  Keep tires free of gasoline and oil, which can harm 

rubber.

NOTE:

 To seal tire punctures and prevent flat tires due to 

slow leaks, tire sealant may be purchased from your local 

parts dealer. Tire sealant also prevents tire dry rot and 

cor ro sion.

MAINTENANCE

GENERAL REC OM MEN DA TIONS

The warranty on this snow thrower does not cover items that 

have been sub ject ed to operator abuse or negligence.  To 

receive full value from the warranty, operator must maintain 

snow thrower as in struct ed in this manual.  Some ad just -

ments will need to be made periodically to properly maintain 

your snow thrower.
At least once a season, check to see if you should make 

any of the adjustments described in the Service and Ad-

 just ments section of this manual.
• 

At least once a year, you should replace the spark plug 

and check belts for wear.  A new spark plug will help 

your engine run better and last longer.

•  Follow the maintenance schedule in this manual.

NOTE:

 Use only Original Equipment Manufacturer (OEM) 

parts to service this unit.  Failure to do so can cause the unit 

to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.  Check engine oil level.
2.  Check for loose fasteners.
3.  Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated

(See “LU BRI CA TION CHART”).

LUBRICATION CHART

 

SAE 5W-30 Motor Oil

 

See “ENGINE” in

Maintenance section

 

General

     Purpose

     Grease

 

Engine oil

 

Pivot 

points

 

Auger

grease fittings

Содержание 414944

































Отзывы: