background image

29

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP13TEPH30

  (96198000900)

CHASSIS / ENGINE / PULLEYS

KEY   PART 

NO.    NO. 

DESCRIPTION

  1  192873 

 Spring, Traction Idler

  2  180522 

 Pulley, Idler (2-1/4)

  3     - - -  

 Engine, Tecumseh, Model Number OH358SA

     

 (For engine service and replacement parts,

     

 call Tecumseh Products at 1-800-558-5402)

  4  74780520 

 Screw, Hex Head  5/16-18 x 1-1/4

  5  150078 

 Screw, Hex Washer Head  5/16-18 x 3/4

 6  59289 

 Washer, Flat

  7  166785 

 Nut, Jam, Lock  5/16-18

  8  175330 

 Pin, Idler Pivot

 9 

405029

 

 V-Belt, Traction Drive

 10  10040500 

 Washer, Lock  5/16

 11  17490508 

 Bolt, Hex Head, Threaded, Rolled  5/16-18 x 1/2

 12  410420 

 Impeller Idler Arm

 13  85179 

 Retainer, Hairpin

 14  178828 

 Spring, Brake

 15 

403842

 

 V-Belt, Impeller Drive

 16  150406 

 Screw, Hex Head  3/8-16 x 1-1/4

 17  187786 

 Arm, Idler

 18  74780524 

 Screw, Hex Head  5/16-18 x 1-1/2

 19  175331 

 Bushing, Idler Pivot

 20  180523 

 Pulley, Idler (2-3/4)

 21  74610516 

 Screw, Hex Head  5/16-18 x 1

 22  409475 

 Spacer, Engine Pulley

 23  180478 

 Pulley, Engine, Traction Drive

 24 

178813

 

 Pulley, Engine, Impeller Drive

 25  400026 

 Washer, Flat  3/8

 26  850263 

 Washer, Lock  3/8

 27  851084 

 Screw, Hex Head  3/8-24 x 1-3/8

 28  193607 

 Guide, Belt

 29 

409161

 

 Belt Cover Assembly (Includes Toolbox Cover)

 30  178830 

 Cover, Toolbox

 31  17490408 

 Screw, Hex Head  1/4-20 x 1/2

 34  198580 

 Clevis Pin

 35  405484 

 Arm, Auger Control

 42  73930500 

 Locknut, Hex

 44  17000616 

 Screw, Hex Head

 45  193397X479   Bracket, Pivot, Idler

 46  403732 

 Pan, Frame Bottom

 47  184471 

 Screw

 49  414997X428   Frame Assembly

 50  192115X428   Plate, Frame End

 51  406109 

 Shaft, Auger Control

 52  57079 

 Washer, Hardened

 57  11050500 

 Washer, Lock, External Tooth  5/16

 58  198563 

 Power Cord

 53  35062 

 Key, Safety

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Содержание 414944

































Отзывы: