background image

11

OPERATION

FIG. 11

TOWING CARTS AND OTHER AT TACH MENTS

Tow only the attachments that are recommended by and 
comply with specifi cations of the manufacturer of your trac-
tor. Use common sense when towing. Too heavy of a load, 
while on a slope, is dangerous. Tires can lose traction with 
the ground and cause you to lose control of your tractor.

TO TRANSPORT (See Figs. 3 and 11)

When pushing or towing your tractor, be sure to disengage 
transmission by placing freewheel control in free wheel ing  
po si tion.  Free wheel control is located at the rear drawbar 
of tractor.
•         Raise attachment lift to highest position with at tach ment 

lift control. 

•      Pull freewheel control out and down into the slot and 

release so it is held in the disengaged position.

•     Do not  push or tow tractor at more than two (2) 

MPH.

•      To reengage transmission, reverse above procedure.

NOTE

:  To protect hood from damage when transporting 

your tractor on a truck or a trailer, be sure hood is closed 
and secured to tractor.  Use an appropriate means of tying 
hood to tractor (rope, cord, etc.).

Transmission Engaged

Transmission Disengaged

ROS "ON" POSITION

ENGINE "ON" POSITION
(NORMAL OPERATING)

02828

TO OPERATE ON HILLS 

CAUTION:  Do not drive up or down hills 
with slopes greater than 15° and do not 
drive across any slope.

•      Choose the slowest speed  before starting up or down 

hills.

•      Avoid stopping or changing speed on hills.
•      If stopping is absolutely necessary, push brake pedal 

quickly to brake position and engage parking brake.

•         To restart movement, slowly release parking brake and 

brake pedal.

•      Slowly depress appropriate drive pedal to slowest set-

 ting.

•      Make all turns slowly.

SERVICE REMINDER/HOUR METER

Service reminder shows the total number of hours the 

engine has run and fl ashes to indicate that the engine 

or mower needs servicing. When service is required, the 

service reminder will fl ash for two hours. To service engine 

and mower, see the Maintenance section of this manual.

NOTE

: Service reminder runs when the ignition key is in 

any position but "STOP". For accurate reading, be sure 

key remains in the "STOP" position when engine is not 

running. 

 WARNING:

  Backing up with the attachment clutch en-

gaged while mowing is strongly discouraged. Turning the 
ROS "ON", to allow reverse operation with the attachment 
clutch engaged, should only be done when the operator 
decides it is necessary to reposition the machine with the 
attachment engaged. 

Do not mow in reverse unless 

absolutely necessary

.

USING THE REVERSE OPERATION SYSTEM -
Only use if you are certain no children or other bystanders 
will enter the mowing area.

•      Depress brake pedal all the way down.
•         With engine running, turn ignition key counterclockwise 

to ROS "ON" position.

•      Look down and behind before and while backing.
•     Slowly depress reverse drive pedal to start move-

ment.

•     When use of the ROS is no longer needed, turn the 

ignition key clockwise to engine "ON" position.

ADD GASOLINE 

•      Fill fuel tank to bottom of fi ller neck. Do not overfi ll.  Use 

fresh, clean, regular un lead ed gasoline with a minimum of 
87 octane.  (Use of  leaded gasoline will increase carbon 
and lead oxide deposits and reduce valve life).  Do not mix 
oil with gasoline.  Purchase fuel in quan ti ties that can be 
used within 30 days to assure fuel freshness.

CAUTION:  Wipe off any spilled oil or 
fuel.  Do not store, spill or use gasoline 
near an open fl ame.

IMPORTANT:

  WHEN OPERATING IN TEMPERATURES 

BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE 
GAS O LINE TO HELP INSURE GOOD COLD WEATHER 
START ING.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor  has been shipped, from the 
factory, already fi lled with sum mer weight oil.  
•      Check engine oil with tractor on level ground.  
•         Remove oil fi ll cap/dipstick and wipe clean, reinsert the 

dipstick and screw cap tight, wait for a few seconds, 
remove and read oil level.  If necessary, add oil until  
“FULL” mark on dipstick is reached.  Do not overfi ll.

•      For cold weather operation you should change oil for 

easier starting (See “OIL VISCOSITY CHART” in the 
Maintenance sec tion of this manual).   

•      To change engine oil, see the Maintenance section in 

this manual.

Содержание 402557































Отзывы: