Poulan Pro 402557 Скачать руководство пользователя

Страница: 20 / 30

02966

02548

PRECISION SIDE-TO-SIDE ADJUSTMENT

(See Fig. 24)
• With all tires properly infl ated, park tractor on level

ground or driveway.

CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.

• Raise mower to its highest position.
• At both sides of mower, position blade at side and

measure the distance (A) from bottom edge of blade
to the ground. The distance should be the same on
both sides.

• If adjustment is necessary, see steps in Visual Adjust-

ment instructions above.

• Recheck measurements, adjust if necessary until both

sides are equal.

NOTE:

Each full turn of the adjustment nut will change

mower height about 1/8".
• Recheck measurements, adjust if necessary until front

tip of blade is 1/8" to 1/2" lower than the rear tip.

• Hold adjustment nut in position with wrench and tighten

jam nut securely against adjustment nut.

FIG. 24

FIG. 25

02950

Tighten adjust nut

to raise mower

Loosen adjust nut

to lower mower

Loosen jam nut

fi rst

FIG. 26

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 27)

MOWER DRIVE BELT REMOVAL
• Park tractor on a level surface. En

gage parking

brake.

• Lower attachment lift lever to its lowest position.
• Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring
loaded. Have a fi rm grip on rod and
release slowly.

• Remove screws (P) from mandrel covers (Q) and re-

move covers.

• Remove any dirt or grass clippings which may have

accumulated around mandrels and entire upper deck
surface.

• Remove belt from electric clutch pulley (M), both man-

drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION
• Install belt around all mandrel pulleys (R) and around

idler pulleys (S) as shown.

• Install belt onto electric clutch pulley (M).

IMPORTANT:

Check belt for proper routing in all mower

pulley grooves.
• Reassemble mandrel covers (Q). Securely tighten all

screws.

• Engage belt tension rod (K) on locking bracket (L).

FRONT-TO-BACK ADJUSTMENT (See Figs. 25 and 26)

IMPORTANT:

Deck must be level side-to-side.

To obtain the best cutting re sults, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" lower than the
rear tip when the mower is in its highest position.

CAUTION:

Blades are sharp. Protect your

hands with gloves and/or wrap blade with
heavy cloth.

• Raise mower to highest position.
• Position any blade so the tip is pointing straight forward.

Measure distance (B) to the ground at front and rear
tip of the blade.

• If front tip of blade is not 1/8" to 1/2" lower than the rear

tip, go to the front of tractor.

• With an 11/16" or adjustable wrench, loosen jam nut

A several turns to clear adjustment nut B.

• With a 3/4" or adjustable wrench, turn front link adjust-

ment nut (B) clockwise (ltighten) to raise the front of
mower, or, counterclockwise (loosen) to lower the front
mower.

Содержание 402557































Результаты поиска

Содержание 402557

Отзывы:

Похожие инструкции для 402557

Бренды по названию

Популярные бренды

Poulan Pro 402557, Руководство оператора

Результаты поиска

Содержание 402557

Отзывы:

Похожие инструкции для 402557

Бренды по названию

Популярные бренды