background image

9400_GB-Anhang A_Sicherheit

SUPPLEMENT - A

Recommendations for work safety 

- A 1 -

20%

Kg

Recommendations for work safety 

All points refering to safety in this manual are indicated 
by this sign.

1.) Defined  use

a.  See "Technical Data". 

b.  The keeping of operating, service and maintenance requirements 

layed down by the manufacturer also come under the heading of 
"defined use".

 

2.) Spare parts

a.  The 

original components and accessories

 have been designed 

 especially for these machines and appliances. 

b.  We want to make it quite clear that components and accesories 

that have not been supplied by us have not been tested by us. 

c.  The installation and/or use of such products can, therefore, 

negatively change or influence the construction characteristics 
of the appliance. We are not liable for damages caused by the 
use of components and accessories that have not been supplied 
by us. 

d.  Alterations and the use of auxiliary parts that are not permitted 

by the manufacturer render all liability invalid. 

3.) Protection devices

   All protection devices must remain on the machine and be 

maintained in proper condition. Punctual replacement of worn 
and damaged covers is essential.

4.) Before starting work

a.  Before commencing work, the operator must be aware of all 

operating devices and functions. The learning of these is too late 
after having already commenced operation!

b. The vehicle is to be tested for traffic and operating safety before 

each operation. 

5.) Asbestos 

-  Certain sub-supplied components of the 

 vehicle may contain asbestos due to technical 
reasons. Observe the warning on spare 
parts. 

6.) Transport of persons prohibited

a.  The transport of persons on the machine is not permitted. 

b.  The machine may only be driven on public roads when in the 

position stipulated for road transport. 

7.) Driving ability with auxiliary equipment 

a.    The towing vehicle is to be sufficiently equiped with weights at the 

front or at the rear in order to guarantee the steering and braking 
capacity (a minimum of 20% of the vehicle’s tare weight on the 
front axle).

b.  The driving ability is 

influenced by ground 
conditions and by the 
 auxiliary equipment. The 
driving must be adapted 
to the corresponding 
 terrain and ground 
 conditions. 

c.  When driving through 

curves with a connected 
 appliance, observe the 
radius and swinging 
mass of the appliance. 

d.  When travelling in a curve with attached or semimounted 

implements, take into account the working range and swing mass 
of the implement!

8.) General 

a.  Before attaching implement to three-point linkage, move system 

lever into a position whereby unintentional raising or lowering is 
ruled out!

b.  Danger of injury exists when coupling implement to tractor!

c.  Danger of injury through crushing and cutting exists in the three-

point linkage area!

d.  Do not stand between tractor and implement when using three-

point linkage external operation!

e.  Attach and detach drive shaft only when motor has stopped.

f.  When transporting with raised implement, secure operating lever 

against lowering! 

g.  Before leaving tractor, lower attached implement to the ground 

and remove ignition key!

h.  Nobody is to stand between tractor and implement without tractor 

being secured against rolling using parking brake and/or wheel 
chocks!

i.   For all maintenance, service and modification work, turn driving 

motor off and remove universal drive.

9.) Cleaning the machine

    Do not use high-pressure washers for the cleaning of bearing- and 

hydraulic parts.

Содержание EUROTOP 340 N



























Отзывы: