Positron 3782101C/50 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 74

background image

Using the Composite Railway-Insulator Tester & Software

32

5.1.7 Get (Firmware) Revision of the Probe

Select

Get Revision of Probe

to receive the Insulator Tester’s internal Firmware Revision level.

Normally, this function is used by Positron Technical Support when troubleshooting the
Insulator Tester. In this instance, the function is used as a confirmation that the Tablet/Laptop
can communicate a command to the Insulator Tester and that the Insulator Tester will respond
via the long range Bluetooth communication through the associated COM Port.

Once you have selected

Get Revision of Probe,

communication between the Tablet and

Insulator Tester is established. Ensure that the Probe is in

Awake Mode

by pressing the push

button of the Insulator Tester Probe. See Figure 11. If required, select

BEEP

after the Probe

is

awakened. The Probe will respond with a BEEP tone.

This  step  verifies  that  the  Tablet/Laptop  can  communicate  with  the  Probe.  Once  Bluetooth
connectivity  and  functional  communication  are  verified,  the  Probe  can  be  switched  off  after
pressing the Close button. The Probe will be switched on again in the field when scanning is to
begin.

Before going out into the field for an insulator scanning session, ensure the Positron Insulator
Tester and Tablet/Laptop are fully charged. The batteries of the Tablet/Laptop are best
maintained for longer life by recharging before the battery charge depletes below 50%.

N

OTE

Figure 11

C-Tester V2.0 60Hz

Example Only

«
...
36
37
38
39
40
...
»

Содержание 3782101C/50











































































Отзывы:

Нет отзывов

Похожие инструкции для 3782101C/50

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: Zenbooth Страницы: 60

Бренд: JB-Lighting Страницы: 60

LOUDEN 200 Series

Бренд: ACCO Brands Страницы: 144

Бренд: B&K Страницы: 16

Бренд: B&G Страницы: 2

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: Ocean Sonics Страницы: 45

Бренд: Vapotherm Страницы: 32

Бренд: Vanguard Instruments Страницы: 47

Бренд: Feniex Страницы: 5

Бренд: V-GREAT Страницы: 4

Бренд: Yacht Devices Страницы: 32

TUV COMFORT LIGHT Series

Бренд: olympia electronics Страницы: 4

Бренд: Lencarta Страницы: 6

Бренд: Feniex Страницы: 5

Бренд: GOZONE Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды