POSIFLEX PP-8000 Скачать руководство пользователя

Страница: 14 / 20

Part 14

when finish. The lock up of the print hood can then be released after this
problem solved.

Please use manual cutter as temporary alternative measure once the

auto cutter malfunctioned.

Advanced Analysis Tool

This printer supports

Hexadecimal Dump

for experienced user to

view exactly what data is received by the printer. This can be useful in finding
software problems.

To start the dump mode: Turn off printer; Open print hood; Hold

down FEED button while turning printer on; Close the hood.

To stop the dump mode: Press the FEED button to print out the last

line; Turn off the printer.

During dump mode: All commands except

DLE EOT

and

DLE ENQ

are disabled.

USEFUL TIPS



Please note that only those qualified technicians may adjust several
jumpers for some technical settings. Please visit our web site

http://www.posiflex.com

http://www.posiflex.com.tw

for details of the

technical information such as driver installation, DIP switch settings and
command sets etc. if required.



Place the printer on a sturdy, level surface.



Choose a place that is well ventilated and free of excessive dust, smoke or
fume.



Do not put the printer under direct sunlight or near a heater.



Ideal room temperature is from 5ºC to 40ºC. Ideal humidity is from 20% to
85% RH (no condensation).



Do not set any liquid or drinks such as coffee on the printer case.



Do not touch any metal part to avoid possible electrostatic damage.



Do not touch the areas around the print head and motor during or right after
printing. It can be very hot.



Do not allow the cut receipt to slide back into the cutter during the
operation. As this would lead to multiple cutting at the lower edge of a
receipt and the multiple cut thin slips tend to cause mechanical malfunction.



Use a grounded AC power outlet with only the power cord and power
adaptor furnished with the printer.



Do not use a power outlet of a circuit shared with any equipment that uses

Содержание PP-8000





















Результаты поиска

Содержание PP-8000

Отзывы:

Похожие инструкции для PP-8000

Бренды по названию

Популярные бренды

POSIFLEX PP-8000, Руководство пользователя

Результаты поиска

Содержание PP-8000

Отзывы:

Похожие инструкции для PP-8000

Бренды по названию

Популярные бренды