background image

Warranty

 

 
Prior to shipment, 

Portwell

 equipment is thoroughly inspected and tested to applicable specifications. However, 

should equipment failure occur, 

Portwell

 assures its customers that prompt service and support will be available. 

All equipment originally manufactured by 

Portwell

 which is found to be defective will be repaired or replaced 

subject to the following considerations. 
 

Terms and Conditions

 

If a unit is suspected of failure, contact 

Portwell

' Customer Service department. Be prepared to give the unit model 

number, serial number, and a description of the failure symptom(s). We may suggest some simple tests to 
confirm the failure. We will assign a Return Material Authorization (RMA) number which must appear on the outer 
label of the return package. All units/components should be properly packed for handling and returned with freight 
prepaid to the 

Portwell

 designated Service Center, and will be returned to the customer's/user's site freight 

prepaid and invoiced. 
 

Coverage

 

First Three Years: Returned unit/part will be repaired and/or replaced at 

Portwell

 option with no charge for labor or 

parts not excluded by warranty. Warranty commences with equipment shipment. 
  
Following Years: Throughout your equipment's lifetime, 

Portwell

 stands ready to provide on-site or in-plant service 

at reasonable rates similar to those of other manufacturers in the industry. 
 

Equipment Not Manufactured by 

Portwell

 

Equipment provided but not manufactured by 

Portwell

 is warranted and will be repaired according to the terms 

and conditions of the respective equipment manufacturer's warranty. 
 

General

 

Under this Warranty, liability of 

Portwell

 is limited to replacing, repairing or issuing credit (at 

Portwell

 discretion) for 

any products which are proved to be defective during the warranty period. In no case is 

Portwell

 liable for 

consequential or special damage arriving from use or misuse of our product. The customer is responsible for all 
charges caused by modifications or additions to 

Portwell

 equipment not approved in writing by 

Portwell

 or, if in 

Portwell

 opinion the equipment has been subjected to abnormal use. "Abnormal use" for purposes of this warranty 
is defined as any use to which the equipment is exposed other than that use specified or intended as evidenced 
by purchase or sales representation. Other than the above, no other warranty, expressed or implied, shall apply to 
any and all such equipment furnished or sold by 

Portwell

 
 

 

Manual PCI-ICM-1S 

3

Содержание PCI-ICM-1S





















Отзывы: