background image

8

•  

Disconnect the charger from the outlet before attempting any cleaning. This will 

reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

•  

NEVER attempt to connect 2 chargers together.

•  

The charger is designed to operate on standard household electrical power (120 

Volts). Do not attempt to use it on any other voltage. 

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY PACKS

WARNING:

 

For safe operation, read this manual and manuals originally supplied 

with tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and 

charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•  

Do not incinerate the battery pack even if it is severely damaged or is completely 

worn out.

 

The battery pack can explode in a fire. Toxic fumes and materials are 

created when LI-ION battery packs are burned.

•  

Do not charge or use battery in explosive atmospheres, such as in the presence of 

flammable liquids, gases or dust. Inserting or removing the battery from the charger 

may ignite the dust or fumes.

•  

If battery contents come into contact with the skin, immediately wash area with 

mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 

15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte 

for Li-ion batteries is composed of a mixture of liquid organic carbonates and lithium salts.

•  

Contents of opened battery cells may cause respiratory irritation. Provide fresh air. 

If symptoms persists, seek medical attention.

WARNING:

 

Burn hazard. Battery liquid may be flammable if exposed to spark or flame. 

•  

Charge the battery packs only in 

 PORTER-CABLE chargers.

•  

DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

•  

Do not store or use the tool and battery pack in locations where the temperature may 

reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).

WARNING:

 

Never attempt to open the battery pack for any reason. If battery pack 

case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery 

pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, 

run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). 

Damaged battery packs should be returned to service center for recycling.

WARNING:

 

Fire hazard. Do not store or carry battery so that metal objects can 

contact exposed battery terminals. For example, do not place battery in aprons, pockets, 

tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. 

Transporting batteries can possibly cause fires if the battery terminals inadvertently 

come in contact with conductive materials such as keys, coins, hand tools and the 

like. The US Department of Transportation Hazardous Material Regulations (HMR) actually 

prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and 

carry-on luggage) UNLESS they are properly protected from short circuits. So when 

transporting individual batteries, make sure that the battery terminals are protected and well 

insulated from materials that could contact them and cause a short circuit.

NOTE:

 LI-ION batteries should not be put in checked baggage.

• 

When using an extension cord, be sure to use one heavy enough to carry the current 

your product will draw. An undersized cord will cause a drop in line voltage resulting 

in loss of power and overheating. The following table shows the correct size to use 

depending on cord length and nameplate ampere rating. If in doubt, use the next 

heavier gage. The smaller the gage number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 

50 ft. 

75 ft. 

100 ft. 

125 ft. 

150 ft. 

175 ft.

7.6 m 

15.2 m 

22.9 m 

30.5 m 

38.1 m 

45.7 m 

53.3 m

Wire Size AWG

18  

18  

16 

16  

14  

14 

12

Содержание PCC792

























































Отзывы: