Polycom EFIR10 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 34

background image

6

Here's how you can determine the status of flow control inside the EF Device:

•

EF2280 (Firmware Version 1.xx), EF200, EF1210:

Flow control is

set to "Automatic" meaning that the unit will not use flow control until it
senses that a cable is connected to the unit that has pins 7 and 8 active.

At that point, the EF Device will assume that flow control is required for all

commands. If you connect to the unit with a cable that does not have
flow control, the EF Device will limit communications with the host since

the EF Device is expecting RTS and CTS to be active. You will still be able
to communicate to the unit, but the rate will be much slower than normal.

To reset the flow control of the unit, cycle power. If the unit powers up

with no cable attached, flow control will be disabled until such time that a
cable with RTS and CTS is connected.

•

EF2280 (Firmware Version 2.0x):

Flow control can be set to "Off",

"On", or "Automatic" via RS-232 commands. "Off" means that flow
control is never enabled and you may connect to the unit with a cable that

supports or doesn't support flow control. "On" means that flow control is

always enabled. You must have a cable that supports RTS or CTS;
otherwise, you will not be able to communicate with the unit. "Automatic"

means that the unit will not use flow control until it senses that a cable is
connected to the unit that has pins 7 and 8 active. At that point, the EF

Device will assume that flow control is required for all commands. If you

connect to the unit with a cable that does not have flow control, the EF
Device will limit communications with the host since the EF Device is

expecting RTS and CTS to be active. You will still be able to communicate
to the unit, but the rate will be much slower than normal.

•

EF2280 (Firmware Version 2.1.0 or higher):

Flow control can be

set to "Off", "On", or "Automatic" via RS-232 commands or via the front
panel under V

ORTEX

S

YSTEM

S

ETTINGS

. "Off" means that flow control is

never enabled and you may connect to the unit with a cable that supports

or doesn't support flow control. "On" means that flow control is always
enabled. You must have a cable that supports RTS or CTS; otherwise,

you will not be able to communicate with the unit. "Automatic" means
that the unit will not use flow control until it senses that a cable is

connected to the unit that has pins 7 and 8 active. At that point, the EF

Device will assume that flow control is required for all commands. If you
connect to the unit with a cable that does not have flow control, the EF

Device will not communicate with the host since the EF Device is
expecting RTS and CTS to be active.

«
...
4
5
6
7
8
...
»

Содержание EFIR10



































Отзывы:

Нет отзывов

Похожие инструкции для EFIR10

Бренд: KAR-TECH Страницы: 28

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: ECKELMANN Страницы: 178

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Бренд: Gate Motors Страницы: 6

Бренд: Walimex Pro Страницы: 68

Бренд: u-blox Страницы: 28

MusicCAST MCX-CA15

Бренд: Yamaha Страницы: 176

Бренд: Wang Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды